2025-06-27

Glare Shield (Remove and Replace)

Correction code 15051302 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1080559-20-A 공구, 토크 스크루드라이버, 0.8-2.0NM (북미, APAC)
  • 1080559-21-A 공구, 토크 스크루드라이버, 0.8-2.0NM (EMEA)

Torque Specifications

표 1. Torque Specifications: Glare Shield (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
전방 카메라 눈부심 방지 실드와 윈드실드 브래킷 패스너
1 Nm (.7 lbs-ft)
  • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
  • Wiha 토크 셋터
  • T10 블레이드 부착물
Replace 패스너에 패치 재질이 있음

Remove

  1. 하단 쿼드 카메라 커버를 탈거합니다. 참조 항목: Quad Camera Cover - Lower (Remove and Replace).
  2. 리어 뷰 미러를 탈거합니다. 참조 항목: Mirror - Rear View (Remove and Replace).
  3. 상단 쿼드 카메라 커버를 고정하는 클립을 분리하고 실내 카메라 커넥터를 연결 해제한 다음, 차량에서 상단 쿼드 카메라 커버와 실내 카메라 어셈블리를 탈거합니다.
  4. 전방 카메라 글레어 실드를 고정하는 패치 나사(2개)를 탈거하여 폐기한 다음 차량에서 글레어 실드를 탈거합니다.

Install

  1. 글라스 클리너 및 깨끗한 타월을 사용하여 카메라 전면의 윈드실드 영역을 완전히 소제합니다.
  2. 정렬 핀을 사용하여 전방 카메라 글레어 실드를 윈드실드 브래킷의 올바른 위치에 배치합니다.
  3. 전방 카메라 글레어 실드를 윈드실드 브래킷에 고정하는 새 패치 나사(2개)를 장착합니다.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
    • Wiha 토크 셋터
    • T10 블레이드 부착물
  4. 실내 카메라 커넥터를 연결한 다음, 상단 쿼드 카메라 커버를 차량에 고정하는 클립을 장착합니다.
  5. 리어 뷰 미러를 장착합니다. 참조 항목: Mirror - Rear View (Remove and Replace).
  6. 하단 쿼드 카메라 커버를 장착합니다. 참조 항목: Quad Camera Cover - Lower (Remove and Replace).