Module - ECU - Occupant Classification System (OCS) - Front Passenger (Remove and Replace)
Correction code
13010012
0.18
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
Remove
- 펌웨어가 버전 2023.2.11 이상인지 확인합니다. 펌웨어 버전이 2023.2.11 이상이 아닌 경우 차량 펌웨어를 업데이트합니다.
- RH 전면 도어를 열고 RH 전면 윈도우를 내립니다.
- 전면 동승석 시트를 앞으로 이동하고 시트를 가장 높은 위치로 올립니다.
-
OCS ECU 모듈에서 자체 정전 용량 트레이스 커넥터를 연결 해제합니다.
-
OCS ECU 모듈에서 RH 전면 시트 하네스 커넥터를 연결 해제합니다.
-
전면 동승석 OCS ECU 모듈을 시트 어셈블리에 고정하는 탭(2개)을 분리한 다음 차량에서 모듈을 탈거합니다.
Install
-
전면 동승석 OCS ECU 모듈을 차량에 배치한 다음 모듈을 시트 어셈블리에 고정하는 탭(2개)을 고정합니다.
-
RH 전면 시트 하네스 커넥터를 OCS ECU 모듈에 연결합니다.
-
자체 정전 용량 트레이스 커넥터를 OCS ECU 모듈에 연결합니다.
- 전면 동승석 시트를 원래 위치로 이동합니다.
- RH 전면 창문을 올리고 RH 전면 도어를 닫습니다.
-
If servicing the front passenger seat in
a North American vehicle:
- Remove all objects from the front passenger seat before beginning calibration.
- On the vehicle touchscreen, touch Software Reinstall - Touchscreen. If the vehicle firmware is not 2023.2.11 or newer, update the vehicle firmware. See Software Update. and check the vehicle firmware version. If the vehicle firmware is 2023.2.11 or newer, perform a software reinstall. See
- Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
- Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
- In Toolbox, click on the Actions tab, and then search for "OCS".
- Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration routine.
- Click on the Actions tab, and then search for "Seat calibration".
- Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate routine.
- Disconnect Toolbox and remove the laptop from the vehicle.