2024-10-15

Software Reinstall - Toolbox

Correction code 00020008 0.05 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-06-08: 리튬 이온 지침을 업데이트했습니다. 차량 소프트웨어 버전 2023.12 이상이 필요하며, "컨택터 닫힘" 및 "컨택터 열림" 절차를 통합했습니다.
Informational PurposesAn informational icon, calling your attention
참고
이 절차에서는 Toolbox 3에 로컬로 연결된 노트북을 사용하여 현재 설치된 차량 소프트웨어를 재설치하는 방법을 설명합니다. 패키지는 Tesla 서버에서 다운로드되지 않습니다.
소프트웨어 재설치 프로세스는 차량에 납산 배터리가 장착되어 있는지 또는 리튬 이온 배터리가 장착되어 있는지에 따라 다릅니다.

펌웨어 재배포(납산 배터리)

  1. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  2. 소프트웨어 재설치 중 전원이 손실되지 않도록 LV 배터리 유지 장치를 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    50A 또는 80A 유지 장치를 사용하는 경우 유지 장치가 "납산" 또는 "반전력" 모드로 설정되었는지 확인합니다. 그렇지 않으면 LV 배터리가 손상될 수 있습니다.
  3. Toolbox 3가 설치된 노트북을 차량에 연결합니다. 참조 항목: Toolbox 3(연결 및 연결 해제).
    Informational PurposesAn informational icon, calling your attention
    참고
    차량을 Toolbox 3에 로컬로 연결하면 정비 모드 플러스가 자동으로 활성화됩니다.
  4. Toolbox에서 Actions/Autodiag 탭을 선택한 다음 "redeploy"를 검색합니다.
  5. UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    • Thermal ➜ HVAC ➜ CAN Redeploy
    • chassis ➜ DPB Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Post Replacement ➜ CAN Redeploy
    • chassis ➜ IDB Post Replacement ➜ CAN Redeploy
    • chassis ➜ RCU Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
    • chassis ➜ IBST Replacement Panel ➜ CAN Redeploy
    루틴을 실행하고 재설치가 완료될 때까지 기다립니다. 차량 터치스크린에서 재설치 상태를 모니터링할 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    • Thermal ➜ HVAC ➜ CAN Redeploy
    • chassis ➜ DPB Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Post Replacement ➜ CAN Redeploy
    • chassis ➜ IDB Post Replacement ➜ CAN Redeploy
    • chassis ➜ RCU Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
    • chassis ➜ IBST Replacement Panel ➜ CAN Redeploy
    이는 차량 컴퓨터를 제외한 모든 모듈, ECU 및 구성품 교체에 현재 설치된 소프트웨어 패키지를 재설치하는 "부분" 소프트웨어 재설치입니다.
  6. 재설치가 완료되면 터치스크린에 재설치 성공을 나타내는 릴리즈 노트가 표시되는지 확인합니다.
  7. LV 배터리 유지 장치를 연결 해제합니다.
  8. 차량에서 노트북을 연결 해제합니다. 참조 항목: Toolbox 3(연결 및 연결 해제).
  9. 정비 모드를 비활성화합니다. 참조 항목: Service Mode.
  10. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).

소프트웨어 재설치(리튬 이온 배터리)

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차를 수행하려면 차량 소프트웨어 버전 2023.12 이상이 필요합니다.
  1. LV 유지 장치를 차량에 연결하되 LV 배터리를 연결 해제하지 않습니다. 참조 항목: LV Maintainer (Connect and Disconnect).
    Informational PurposesAn informational icon, calling your attention
    참고
    이 절차를 수행하는 동안 LV 유지 장치 및 LV 배터리가 모두 연결되어 있어도 괜찮습니다.
  2. Toolbox 3가 설치된 노트북을 차량에 연결합니다. 참조 항목: Toolbox 3(연결 및 연결 해제).
    Informational PurposesAn informational icon, calling your attention
    참고
    차량을 Toolbox 3에 로컬로 연결하면 정비 모드 플러스가 자동으로 활성화됩니다.
  3. Toolbox에서 Actions/Autodiag 탭을 선택한 다음 "redeploy"를 검색합니다.
  4. UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    • Thermal ➜ HVAC ➜ CAN Redeploy
    • chassis ➜ DPB Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Post Replacement ➜ CAN Redeploy
    • chassis ➜ IDB Post Replacement ➜ CAN Redeploy
    • chassis ➜ RCU Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
    • chassis ➜ IBST Replacement Panel ➜ CAN Redeploy
    루틴을 실행하고 재설치가 완료될 때까지 기다립니다. 차량 터치스크린에서 재설치 상태를 모니터링할 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    • Thermal ➜ HVAC ➜ CAN Redeploy
    • chassis ➜ DPB Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Post Replacement ➜ CAN Redeploy
    • chassis ➜ IDB Post Replacement ➜ CAN Redeploy
    • chassis ➜ RCU Post Replacement ➜ CAN Redeploy
    • chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
    • chassis ➜ IBST Replacement Panel ➜ CAN Redeploy
    이는 차량 컴퓨터를 제외한 모든 모듈, ECU 및 구성품 교체에 현재 설치된 소프트웨어 패키지를 재설치하는 "부분" 소프트웨어 재설치입니다.
  5. 재설치가 완료되면 터치스크린에 재설치 성공을 나타내는 릴리즈 노트가 표시되는지 확인합니다.
  6. 차량에서 LV 유지 장치를 연결 해제합니다. 참조 항목: LV Maintainer (Connect and Disconnect).
  7. 차량에서 노트북을 연결 해제합니다. 참조 항목: Toolbox 3(연결 및 연결 해제).
  8. 정비 모드를 비활성화합니다. 참조 항목: Service Mode.
  9. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).