Hub - Front - LH (RWD) (Remove and Replace)
Correction code
31010602
0.24
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
- 2025-04-02: 브레이크 로터 탈거 및 장착 절차를 업데이트했습니다.
- 1062500-00-A 카드, 자기장 뷰어
- 1082171-00-A S자형 후크
토크 규격
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
LH 전면 허브를 너클에 고정하는 볼트 |
![]() 85 Nm (62.7 lbs-ft) |
|
Reuse |
Remove
- LH 전면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
-
LH 전면 브레이크 호스 브래킷을 LH 전면 너클에 고정하는 볼트를 탈거합니다.5 Nm (3.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10mm 소켓
- 육각 헤드 래칫/플렉스 헤드 토크 렌치
- 4인치 익스텐션
-
LH 전면 캘리퍼를 LH 전면 너클에 고정하는 볼트를 탈거하여 폐기하고 너클에서 캘리퍼를 탈거한 다음 캘리퍼가 S자형 후크에 걸리게 합니다.94 Nm (69.3 lbs-ft)TIpUse of the following tool(s) is recommended:
- 외부 Torx E18
- 래칫/토크 렌치
참고필요한 경우 캘리퍼 스프레더 도구를 사용하여 캘리퍼 피스톤을 완전 개방 위치로 밉니다. -
브레이크 로터를 허브에 고정하는 볼트를 탈거한 다음 허브에서 브레이크 로터를 탈거합니다.5 Nm (3.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10mm 소켓
- 육각 헤드 래칫/플렉스 헤드 토크 렌치
- 2인치 익스텐션
-
LH 전면 허브를 너클에 고정하는 볼트를 탈거한 다음 차량에서 허브를 탈거합니다.
TIp다음 공구 사용을 권장합니다.
- 18mm 소켓
- 3인치 익스텐션
Install
- 장착하기 전에 LH 전면 허브의 톤 링을 확인합니다. 자기장 뷰어 카드를 사용하여 톤 링의 자기장이 손상되지 않았는지 확인합니다.
-
LH 전면 허브를 너클에 배치한 다음 허브를 너클에 고정하는 볼트를 장착합니다.85 Nm (62.7 lbs-ft)TIp다음 공구 사용을 권장합니다.
- 18mm 소켓
- 3인치 익스텐션
-
브레이크 로터를 허브에 배치한 다음, 로터를 허브에 고정하는 볼트를 장착합니다.5 Nm (3.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10mm 소켓
- 육각 헤드 래칫/플렉스 헤드 토크 렌치
- 2인치 익스텐션
-
LH 전면 캘리퍼를 LH 전면 너클에 배치한 다음 캘리퍼를 너클에 고정하는 새 볼트를 장착합니다.94 Nm (69.3 lbs-ft)TIpUse of the following tool(s) is recommended:
- 외부 Torx E18
- 래칫/토크 렌치
참고필요한 경우 캘리퍼 스프레더 도구를 사용하여 캘리퍼 피스톤을 완전 개방 위치로 밉니다. -
LH 전면 브레이크 호스 브래킷을 LH 전면 너클에 배치한 다음 브래킷을 너클에 고정하는 볼트를 장착합니다.5 Nm (3.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10mm 소켓
- 육각 헤드 래칫/플렉스 헤드 토크 렌치
- 4인치 익스텐션
- LH 전면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
- Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See 얼라인먼트 요구 사항 - 서스펜션.