2024-11-22

Active Grille Shutter (Heat Pump) (Remove and Replace)

Correction code 18500612 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-11-13: 최신 검증에 따라 전체 절차를 업데이트했습니다.
표 1. Torque Specifications: Active Grille Shutter (Heat Pump) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
냉각 팬 모듈 어셈블리를 전면 엔드 캐리어에 고정하는 LH 및 RH 볼트(2개)
10 Nm (7.4 lbs-ft)
  • 8mm 소켓
  • 6인치 익스텐션
  • 유니버설 조인트 1/4인치
  • 코드리스 래칫/임팩트 드라이버
  • 래칫/토크 렌치 (장착 시에만 사용)
Reuse

Remove

  1. 차량을 2-포스트 리프트에 놓습니다.
  2. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  3. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  4. LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. 커넥터 잠금 장치를 분리한 다음 액티브 그릴 셔터 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 탭을 누르지 마십시오. 빨간색 탭을 당겨 커넥터 잠금 장치를 분리합니다.
  6. 액티브 그릴 셔터에서 외기 온도 센서 커버를 탈거한 다음 센서 전기 커넥터를 연결 해제합니다.
  7. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  8. 전면 밸런스를 탈거합니다. 참조 항목: Valance - Front Fascia (Remove and Replace).
  9. 전면 서브프레임에 타월을 놓아 이후 단계에서 냉각 팬을 보호합니다.
  10. 보조 작업자가 냉각 팬 모듈 어셈블리를 지지하는 동안 냉각 팬 모듈 어셈블리를 전면 엔드 캐리어에 고정하는 LH 및 RH 볼트(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 소켓
    • 6인치 익스텐션
    • 유니버설 조인트 1/4인치
    • 코드리스 래칫/임팩트 드라이버
    • 래칫/토크 렌치 (장착 시에만 사용)
    그림 1. LH
    그림 2. RH
  11. 차량을 작업하기 편안한 높이로 내리고 리프트를 잠금 장치에 고정합니다.
  12. 액티브 그릴 셔터를 냉각 팬 및 슈라우드 어셈블리에 고정하는 잠금 탭(14개)을 분리한 다음 액티브 그릴 셔터를 탈거합니다.

Install

  1. 액티브 그릴 셔터를 냉각 팬 및 슈라우드 어셈블리에 장착한 다음 셔터를 어셈블리에 고정하는 잠금 탭을 조입니다.
  2. 차량을 작업하기 편안한 높이로 높인 다음, 리프트를 잠금 장치까지 내립니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고

    차량을 내리기 전에 잠금 장치 양쪽에서 딸깍 소리가 들리는지 확인하십시오. 그렇지 않으면 차량이 한쪽으로 기울 수 있습니다.

    도어 주변에 물체가 없는지 확인하십시오.

  3. 보조 작업자가 냉각 팬 모듈 어셈블리를 지지하는 동안 냉각 팬 모듈 어셈블리를 전면 엔드 캐리어에 고정하는 LH 및 RH 볼트(2개)를 규격 토크로 조입니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 소켓
    • 6인치 익스텐션
    • 유니버설 조인트 1/4인치
    • 코드리스 래칫/임팩트 드라이버
    • 래칫/토크 렌치 (장착 시에만 사용)
    그림 3. LH
    그림 4. RH
  4. 전면 서브프레임에서 타월을 제거합니다.
  5. 전면 밸런스를 장착합니다. 참조 항목: Valance - Front Fascia (Remove and Replace).
  6. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  7. 타이어가 지면에 닿을 때까지 차량을 내립니다.
  8. 외기 온도 센서 전기 커넥터를 연결한 다음 센서 커버를 액티브 그릴 셔터에 장착합니다.
  9. 잠금 탭을 체결하여 액티브 그릴 셔터 전기 커넥터를 연결합니다.
  10. LV 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  11. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCFRONT_X_LOUVER-CALIBRATIONvia Toolbox: (link)
    Informational PurposesAn informational icon, calling your attention
    참고
    완료되면 창 오른쪽 상단에 있는 'X'를 선택하여 닫습니다.
  12. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    Informational PurposesAn informational icon, calling your attention
    참고
    완료되면 창 오른쪽 상단에 있는 'X'를 선택하여 닫습니다.
  13. 정비 모드를 비활성화합니다. 참조 항목: Service Mode.
  14. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  15. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.
  16. 리프트에서 차량을 내립니다.