2023-11-05

Latch Actuator - Charge Port (Remove and Replace)

Correction code 44014002 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-10-27: 차체 쪽 충전 포트(CP) 볼트 토크를 9Nm으로 업데이트합니다.
  • 2023-10-10: 충전 포트 도어를 수동으로 닫지 않도록 하라는 주의 사항을 추가했습니다.
  • 2023-05-24: 차량 전기 절연 절차를 삭제했습니다.
  • 1076921-00-B 절연 멀티미터, Fluke 1507(북미)
  • 1076921-00-A 절연 멀티미터, Fluke 1587(유럽/중동/아프리카)
  • 1076921-01-B 절연 멀티미터, Fluke 1508(APAC)
  • 1108272-00-B 캡, 로직 연결, 인버터, 3DU
  • 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.

  • 고전압(HV) 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.

Remove

  1. 트렁크를 엽니다.
  2. 충전 포트 도어를 엽니다.
  3. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  4. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  5. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 충전 포트 전압 점검 절차를 수행합니다. 참조 항목: Charge Port Voltage Check.
  7. LH 트렁크 사이드 트림을 탈거합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  8. 저전압 전기 배선 하네스를 충전 포트 클로즈아웃 패널에 고정하는 클립을 해제합니다.
  9. 충전 포트 클로즈아웃 패널을 둘러싼 탭을 해제하고 차량에서 패널을 탈거합니다.
  10. 충전 포트 전기 접지를 차체에 고정하는 볼트를 탈거합니다.
  11. 충전 포트 어셈블리를 차체에 고정하는 볼트를 탈거합니다.
  12. 충전 포트 전기 배선 하네스를 차체에 고정하는 클립을 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    접근을 위해 차체에서 충전 포트(CP)를 분리합니다.
  13. 래치 액추에이터에서 릴리스 암을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    래치 액추에이터에서 릴리스 암을 탈거하기 전에 릴리스 암의 방향에 유의하십시오.
  14. 래치 액추에이터 커넥터를 연결 해제합니다.
  15. 래치 액추에이터를 충전 포트에 고정하는 나사를 탈거하고 차량에서 래치 액추에이터를 탈거합니다.

Install

  1. 차량에 새 래치 액추에이터를 장착합니다.
  2. 래치 액추에이터를 충전 포트에 고정하는 나사를 장착합니다.
    1.2 Nm (.9 lbs-ft)
  3. 래치 액추에이터 커넥터를 연결합니다.
  4. 릴리스 암을 탈거했을 때와 동일한 위치의 래치 액추에이터에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    장착 후, 릴리스 암을 수동으로 회전시켜 래치 액추에이터가 움직이는지 확인합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    아래 그림과 같이 래치 액추에이터의 방향이 올바른지 확인하십시오. 잘못 장착하면 제대로 걸리지 않을 수 있습니다.
  5. 차체에 충전 포트 전기 배선 하네스를 고정하는 클립을 장착합니다.
  6. 차체에 충전 포트 어셈블리를 고정하는 볼트를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하네스가 배선되어 있고 케이블타이가 있는 접착제 패드가 장착된 경우 올바르게 장착되어 있는지 확인합니다.
  7. 차체에 충전 포트 전기 접지를 고정하는 볼트를 장착합니다.
    6 Nm (4.4 lbs-ft)
  8. 차량에 충전 포트 클로즈아웃 패널을 장착합니다. 패널을 클립(7개)으로 고정합니다.
  9. 충전 포트 클로즈아웃 패널에 저전압 전기 배선 하네스 클립을 장착합니다.
  10. LH 트렁크 사이드 트림을 장착합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  11. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  12. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  13. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  14. 후드, 트렁크 및 충전 포트 도어를 닫습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    충전 포트 도어를 수동으로 닫지 않도록 하십시오.
  15. 충전 시스템 작동을 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    고객의 충전 장비가 있는 경우, 해당 장비를 사용합니다.
    1. 충전 포트 도어의 하단 RH 모서리를 살짝 눌러 충전 포트(CP)를 연 다음 충전 포트 도어를 닫습니다.
    2. UMC 또는 월 커넥터를 사용하고 핸들의 버튼을 눌러 충전 포트 도어를 엽니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      도어를 닫은 후 도어가 다시 열릴 때까지 잠시 제한 시간이 경과될 수 있습니다.
    3. 충전 핸들을 충전 포트(CP)에 연결하고 차량이 충전 중인지 확인하십시오.
    4. 충전 핸들을 분리하고 충전 포트 도어가 닫히는지 확인합니다.