2024-10-09

Check Valve - Evaporator (Heat Pump) (Remove and Replace)

Correction code 18401002 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-01-23: 루틴 수행 방법을 Toolbox를 사용하는 방법에서 터치스크린을 사용하는 방법으로 업데이트했습니다.
  • 2023-04-04: A/C 오일 규격에 대한 유액 및 용량을(를) 참조하여 사용할 A/C 오일 유형을 업데이트했습니다.
Informational PurposesAn informational icon, calling your attention
참고
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  2. 터치스크린을 사용하여 차량을 정비 모드로 전환합니다. 참조 항목: Service Mode.
  3. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  4. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  5. 터치스크린에서 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Thermal > Refrigerant System > Start Thermal Fill Drain (Refrigerant only) > Run을 탭하고 루틴이 완료될 때까지 기다립니다.
  6. A/C 냉매를 회수합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
  7. 슈퍼매니폴드에서 증발기 체크 밸브 스냅 링을 탈거하여 폐기합니다.
  8. 슈퍼매니폴드에서 증발기 체크 밸브를 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    탈거 도중 체크 밸브가 알루미늄 캡에서 분리되는 경우, 금속 도구를 사용하지 마십시오. 금속 도구는 슈퍼매니폴드 하우징을 긁어 내부 손상이 발생할 수 있습니다. 그 대신 손가락을 사용하거나 90도 픽 공구에 전기 테이프를 감싸서 사용하십시오.

Install

  1. 적절한 A/C 오일로 O링을 윤활합니다. A/C 오일 규격은 유액 및 용량을(를) 참조하십시오. 그런 다음 체크 밸브를 슈퍼매니폴드에 장착합니다.
  2. 슈퍼매니폴드에 증발기 체크 밸브 스냅 링을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스냅 링이 슈퍼매니폴드의 홈 내부에 완전히 안착되었는지 확인하십시오.
  3. 진공 누출 테스트를 수행하고 A/C 냉매를 보충합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
  4. 터치스크린에서 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Thermal > Sensors and Valves > Run Heat Pump Commissioning > Run을 탭하고 루틴이 완료될 때까지 기다립니다.
  5. Actions > Test Thermal Performance를 탭하고 Run을 선택한 다음 루틴이 완료될 때까지 기다립니다.
  6. Actions > Test HVAC Performance를 탭하고 Run을 선택한 다음 루틴이 완료될 때까지 기다립니다.
  7. 정비 모드를 비활성화합니다. 참조 항목: Service Mode.
  8. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  9. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.