2020-02-26

Box Clip - Seat Belt Reminder - 1st Row - LH (Remove and Replace)

Correction code 20051102 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Seat Assembly - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
전면 시트를 차체에 고정하는 볼트
33.5 Nm (24.7 lbs-ft)
  • Trox Plus T45 소켓
  • 3/8인치 표준 플렉스 헤드 래칫
  • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
Replace 볼트가 패치되어 있음

Remove

  1. LH 도어를 모두 열고 LH 윈도우를 모두 내립니다.
  2. 시트를 앞으로 끝까지 이동합니다.
  3. 운전석 시트의 뒤쪽을 차체에 고정하는 패치 볼트(2개)를 탈거하여 폐기합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 3/8인치 표준 플렉스 헤드 래칫
    • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
  4. 시트를 뒤로 끝까지 이동합니다.
  5. 운전석 시트의 앞쪽을 차체에 고정하는 패치 볼트(2개)를 탈거하여 폐기합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 3/8인치 표준 플렉스 헤드 래칫
    • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
  6. 시트를 뒤쪽으로 기울여 시트 쿠션 아래쪽에 접근합니다.
  7. 시트 프레임에 안전벨트 경고 장치를 고정하는 클립을 분리합니다
  8. 안전벨트 경고 장치에 안전벨트 경고 장치 박스 클립을 고정하는 고정 탭(2개)을 해제합니다. 차량에서 안전벨트 경고 장치 박스 클립을 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    전기 커넥터를 연결 해제하지 마십시오.

Install

  1. 안전벨트 경고 장치 박스 클립을 제자리로 이동한 다음 안전벨트 경고 장치에 안전벨트 경고 장치 박스 클립을 고정하는 고정 탭(2개)을 고정합니다.
  2. 시트 프레임에 안전벨트 경고 장치를 고정하는 클립을 고정합니다
  3. 시트를 앞으로 기울여 제자리에 오게 하고 시트 레일의 구멍을 차체의 구멍과 맞춥니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    시트를 앞으로 기울일 때 카펫 또는 트림 패널이 손상되지 않도록 주의해야 합니다.
  4. 새 패치 볼트(2개)를 장착하여 시트 앞쪽을 차체에 고정합니다.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 조입니다.
  5. 시트를 앞으로 끝까지 이동합니다.
  6. 새 패치 볼트(2개)를 장착하여 시트 뒤쪽을 차체에 고정합니다.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 조입니다.
  7. 모든 도어를 닫고 모든 창문을 올립니다.