2025-09-23

Replacement Keys - Program (No Keys Present)

Correction code -리모트키: 17450513 키 카드: 17450306 0.06 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-04-16: 정비 모드 지침을 업데이트하였습니다.
  • 2023-07-21: 보안 관련 Toolbox 작업에 대한 참고 사항을 추가했습니다.
Informational PurposesAn informational icon, calling your attention
참고
Some of the Toolbox Actions within this procedure are related to vehicle security, and can only be performed by Tesla employees or third parties authorized to perform security-related Toolbox Actions. To learn more, see the Service Subscription FAQs available in the user account dropdown menu.
Informational PurposesAn informational icon, calling your attention
참고
이 절차는 두 개의 키를 인증하며 인증된 키가 없거나 보안 컨트롤러(SEC)를 교체한 경우에만 수행해야 합니다. 인증된 키를 사용할 수 있는 경우 Additional Key - Program (Existing Key Present)을(를) 참조하십시오.
Informational PurposesAn informational icon, calling your attention
참고
차량은 최대 19개의 키를 지원합니다. 이 한계에 도달하면 키를 삭제해야만 새 키를 추가할 수 있습니다.

Procedure

  1. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCSEC_C_PAIR-NFC-CARD-V2via Toolbox: (link)via Service Mode: Low Voltage ➜ Keys ➜ Pair Key
  2. NFC 카드를 센터 콘솔의 NFC 카드 리더에 놓습니다.
  3. 차량에 페어링할 키 개수를 입력하고 Run Network를 선택한 다음 루틴이 완료될 때까지 기다립니다.
  4. 루틴이 완료되면 올바른 수의 연결된 키가 표시되는지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    성공적으로 연결된 키 수가 요청한 키 수와 일치하지 않으면 센터 콘솔 또는 휴대폰 거치대의 키 위치를 변경하고 1단계부터 반복합니다.
  5. 각 새 키를 운전석 쪽 B필러 아플리케에 대서 키가 차량을 잠그고 잠금 해제하는지 확인합니다.
  6. 각 새 키를 센터 콘솔 위의 컵 홀더 뒤에 있는 키 리더에 놓아 키가 인증되어 차량을 시동할 수 있는지 확인합니다.