2024-04-08

Coolant Bottle (Heat Pump) (Remove and Replace)

Correction code 18401702 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Coolant Bottle (Heat Pump) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
냉각수 보틀 측면을 슈퍼매니폴드에 고정하는 나사
5 Nm (3.7 lbs-ft)
  • Torx T25 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
냉각수 용기 전면을 슈퍼매니폴드에 고정하는 나사
5 Nm (3.7 lbs-ft)
  • Torx T25 소켓
  • 10인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  2. 외기 흡기 덕트를 탈거합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  3. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  4. 12V 보조 배터리를 탈거합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  5. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  6. 냉각수 보틀 캡을 탈거합니다.
  7. 액체 배출기를 차량 전면 근처에 배치하고 배출기를 "배출" 모드로 설정합니다.
  8. 배출 호스를 냉각수 보틀의 전면 LH 모서리에 배치한 다음 냉각수를 가능한 한 많이 배출합니다.
  9. 잠금 탭을 푼 다음 냉각수 보틀 수위 센서에서 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  10. 전기 하네스를 냉각수 보틀 위에 고정하는 클립을 풉니다.
  11. 냉각수 보틀 근처에 있는 칠러-배터리 호스의 센서에서 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터 하네스를 감싸는 테이프의 색상과 냉각수 보틀과 관련된 하네스의 위치를 기록합니다.
  12. 냉각수 보틀 근처에 있는 파워트레인 공급 호스의 센서에서 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터 하네스를 감싸는 테이프의 색상과 냉각수 보틀과 관련된 하네스의 위치를 기록합니다.
  13. 스프링 클립을 푼 다음, 슈퍼매니폴드에서 칠러-배터리 호스를 탈거합니다.
  14. 스프링 클립을 분리한 다음 슈퍼매니폴드에서 파워트레인 공급 호스를 탈거합니다.
  15. 전기 하네스를 냉각수 보틀 RH 쪽에 고정하는 클립을 풉니다.
  16. 전기 하네스를 냉각수 보틀 LH 쪽에 고정하는 클립을 풉니다.
  17. 냉각수 보틀 측면을 슈퍼매니폴드에 고정하는 나사를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  18. 냉각수 보틀 전면을 슈퍼매니폴드에 고정하는 나사를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 10인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  19. 슈퍼매니폴드에서 냉각수 보틀을 분리하고 보틀을 차량 후면을 향해 이동하여 탈거합니다.

Install

  1. 냉각수 보틀 아래의 O링이 올바르게 안착했는지 확인한 다음 O링에 윤활제를 도포합니다.
  2. 냉각수 보틀을 슈퍼매니폴드에 배치하여 냉각수 보틀 배출구가 슈퍼매니폴드 냉각수 유입구에 완전히 안착되는지 확인합니다.
    그림 1. 슈퍼매니폴드 냉각수 유입구
  3. 냉각수 보틀 측면을 슈퍼매니폴드에 고정하는 나사를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  4. 냉각수 보틀 전면을 슈퍼매니폴드에 고정하는 나사를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 10인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  5. 전기 하네스를 냉각수 보틀 하단 LH 쪽에 고정하는 클립을 장착합니다.
  6. 전기 하네스를 냉각수 보틀 RH 쪽에 고정하는 클립을 장착합니다.
  7. 파워트레인 공급 호스를 슈퍼매니폴드에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  8. 칠러-배터리 호스를 슈퍼매니폴드에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  9. 전기 커넥터를 냉각수 보틀 근처에 있는 파워트레인 공급 호스의 센서에 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 잠금 탭을 커넥터에 밀어 잠금 장치를 체결합니다. 잠금 탭을 측면 방향으로 밀지 마십시오.
  10. 전기 커넥터를 냉각수 보틀 근처에 있는 칠러-배터리 호스의 센서에 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 잠금 탭을 커넥터에 밀어 잠금 장치를 체결합니다. 잠금 탭을 측면 방향으로 밀지 마십시오.
  11. 전기 하네스를 냉각수 보틀 위에 고정하는 클립을 장착합니다.
  12. 전기 커넥터를 냉각수 보틀 수위 센서에 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 잠금 탭을 커넥터에 밀어 잠금 장치를 체결합니다. 잠금 탭을 측면 방향으로 밀지 마십시오.
  13. 냉각수 보틀에 올바른 냉각수를 MAX 선까지 채웁니다.
  14. 12V 보조 배터리를 장착합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  15. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  16. Toolbox가 설치된 노트북을 차량에 연결합니다.
  17. Actions/Autodiag(작업/자동 진단) 탭을 선택하고 “Purge(배출)”를 검색합니다.
  18. TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    옆에 있는 "play" 버튼을 클릭한 다음, RUN 을 선택합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    차량이 주행 상태가 아닌지 확인하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    테스트는 약 10분이 걸립니다. 테스트가 진행되는 동안 슈퍼보틀을 모니터링하고 슈퍼보틀에 냉각수를 완전히 채웁니다. Coolant pump speeds can be monitored in Service Mode + (see Service Mode Plus), in the CAN Viewer submenu. 펌프 속도가 6900rpm 이상으로 유지되면 여전히 시스템에 공기가 갇혀 있는 것입니다. 냉각 시스템 진공 보충을 실행합니다.
  19. 공기 배출이 완료되면 창 오른쪽 상단에 있는 “X”를 클릭합니다.
  20. 냉각수 보틀 수위를 확인하고 필요한 경우 보충합니다.
  21. 냉각수 보틀 캡을 장착합니다.
  22. Toolbox에서 Actions/Autodiag 탭을 선택한 다음 "Thermal"을 검색합니다.
  23. TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    을(를) 클릭한 다음 Run을 클릭합니다.
  24. 루틴이 끝나면 메시지 오른쪽 상단의 "X"를 클릭합니다.
  25. 차량에서 노트북을 연결 해제합니다.
  26. 외기 흡기 덕트를 장착합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  27. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  28. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).