10/08/2023 00:45:52

글로브박스 - 무릎 에어백 포함(히트 펌프)(탈거 및 교체)

교정 코드 14051022 0.42 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

  1. Open both front doors
  2. Lower both front windows
  3. Move RH front seat backward
  4. Open hood
    Informational PurposesAn informational icon, calling your attention
    참고
    Press "Open" button on touchscreen to release latch, Lift lid manually
  5. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    참고
    12x clips, Only store rear apron visible face upwards
  6. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  7. Disconnect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    참고
    1x nut, 10mm, 6 Nm, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
  8. Disconnect first responder loop
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Release locking tab
  9. Remove LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  10. Remove LH air wave bezel cap from main decor assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, Newer vehicles are equipped with solid bezel.
  11. Remove RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  12. Remove RH air wave bezel cap from main decor assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, Newer vehicles are equipped with solid bezel.
  13. Remove main decor assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    15x clips, Entire decor does not need to come off for glove box removal, If you lift RH side of decor then you will have access to 3x torx screws securing top of glove box, Replace securing clips as needed
  14. Release RH footwell assembly from IP
    Informational PurposesAn informational icon, calling your attention
    참고
    4x push clips
  15. Remove RH footwell assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors
  16. Remove bolts securing passenger knee air bag onto vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    4x patch bolts, T30, 8 Nm, Discard after removal, 2x screws, T20, 2 Nm, 1x push clip, Newer vehicles have 4x E10 patch bolts
  17. Remove passenger knee air bag from vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Release locking tab, Connector release may vary
  18. Disconnect glove box USB cable from car computer
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Depress latch on top of USB cable to release internal latches, then release from car computer
  19. Remove screws securing glove box assembly to IP carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    6x screws, T20, 2.3 Nm
  20. Remove glove box from IP carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  21. Disconnect glove box assembly connectors
    Informational PurposesAn informational icon, calling your attention
    참고
    3x electrical connectors

장착

  1. Connect glove box assembly connectors
    Informational PurposesAn informational icon, calling your attention
    참고
    3x connectors, New puddle lamp harness routing prevent blocking movement of pawls, Make sure harness is routed properly above passenger footwell air duct before connecting
  2. Install glove box into IP carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  3. Install screws securing glove box assembly to IP carrier
    Informational PurposesAn informational icon, calling your attention
    참고
    6x screws, T20, 2.3 Nm
  4. Connect glove box USB cable to car computer
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  5. Install passenger knee air bag onto vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Use caution not to damage connector and harness, Support knee air bag while connecting connector
  6. Install bolts securing passenger knee air bag to vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 1x push clip, If vehicle equipped with T30 bolts update to E10
  7. Position RH footwell assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors
  8. Install RH footwell assembly onto IP
    Informational PurposesAn informational icon, calling your attention
    참고
    4x push clips
  9. Install main decor assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    15x clips, 1x center clip
  10. Install RH air wave bezel cap to main decor assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, Newer vehicles are equipped with solid bezel.
  11. Install RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  12. Install LH air wave bezel cap to main decor assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, Newer vehicles are equipped with solid bezel.
  13. Install LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  14. Connect first responder loop
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Engage locking tab, Connect FRL before connecting 12V to avoid damage to car computer
  15. Connect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    참고
    1x nut, 10mm, 6 Nm
  16. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    참고
    12x clips
  17. Close hood
  18. Move RH front seat to original position
  19. Raise LF and RF windows
  20. Close both front doors