2020-03-13

Glove Box - With Knee Airbags (Non-Heat Pump) (Remove and Replace)

Correction code 14051002 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Glove Box - With Knee Airbags (Non-Heat Pump) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
글로브박스를 IP 캐리어에 고정하는 나사(6개)
2.3 Nm (1.7 lbs-ft)
  • Torx T20 소켓
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
  • 4인치 익스텐션
Reuse

Remove

  1. 필요한 경우 글로브박스에서 고객의 물건을 제거하여 안전하게 보관합니다.
  2. 2열 하단 시트 쿠션을 탈거합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  3. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  4. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  5. LH 및 RH 계기판 엔드 캡을 탈거합니다. End Cap - Instrument Panel - LH (Remove and Replace)을(를) 참조하십시오.
  6. RH 중간 A필러 트림을 탈거합니다. Trim - A-Pillar - Middle - LH (Remove and Replace)을(를) 참조하십시오.
  7. RH 하단 A필러 트림을 탈거합니다. Trim - A-Pillar - Lower - LH (Remove and Replace)을(를) 참조하십시오.
  8. 동승석 발밑 공간 커버를 탈거합니다. Cover - Footwell - Passenger (LHD) (Remove and Replace)을(를) 참조하십시오.
  9. 전면 동승석 무릎 에어백을 탈거합니다. Airbag - Knee - Front Passenger (Remove and Replace)을(를) 참조하십시오.
  10. 주 계기판 장식 트림을 탈거합니다. Decor Trim - Instrument Panel - Main (Remove and Replace)을(를) 참조하십시오.
  11. 글로브박스를 IP 캐리어에 고정하는 나사(6개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구를 사용할 것을 권장합니다.
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    • 4인치 익스텐션
  12. 글로브박스를 IP 캐리어에 고정하는 클립을 분리합니다.
  13. 글로브박스 솔레노이드 커넥터, 댐퍼 커넥터, 퍼들 램프 커넥터에서 전기 하네스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전기 커넥터 중 2개는 계기판 하단으로 접근합니다.
  14. 차량에서 글로브박스를 탈거합니다.

Install

  1. 글로브박스를 차량으로 가져온 후 글로브박스 솔레노이드 커넥터, 댐퍼 커넥터, 퍼들 램프 커넥터에 전기 하네스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전기 커넥터 중 2개는 계기판 하단으로 접근합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    퍼들 램프 전기 하네스를 그림과 같이 배치합니다.
    그림 1. 글로브박스 하네스 커넥터
    그림 2. 퍼들 램프 하네스 배치
  2. 글로브박스 댐퍼 핀이 완전히 안착했는지 확인합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    글로브박스를 장착할 때, 글로브박스 댐퍼가 부딪히지 않게 하십시오.
  3. 글로브박스를 IP 캐리어에 고정하는 클립을 조입니다.
  4. 글로브박스를 IP 캐리어에 고정하는 나사(6개)를 장착합니다.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    • 4인치 익스텐션
  5. 주 계기판 장식 트림을 장착합니다. Decor Trim - Instrument Panel - Main (Remove and Replace)을(를) 참조하십시오.
  6. 전면 동승석 무릎 에어백을 장착합니다. Airbag - Knee - Front Passenger (Remove and Replace)을(를) 참조하십시오.
  7. 동승석 발밑 공간 커버를 장착합니다. Cover - Footwell - Passenger (LHD) (Remove and Replace)을(를) 참조하십시오.
  8. RH 하단 A필러 트림을 장착합니다. Trim - A-Pillar - Lower - LH (Remove and Replace)을(를) 참조하십시오.
  9. RH 중간 A필러 트림을 장착합니다. Trim - A-Pillar - Middle - LH (Remove and Replace)을(를) 참조하십시오.
  10. LH 및 RH 계기판 패널 엔드 캡을 장착합니다. End Cap - Instrument Panel - LH (Remove and Replace)을(를) 참조하십시오.
  11. 12V 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  12. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  13. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  14. 글로브박스 도어가 정상적으로 열리는지 터치스크린을 통해 확인합니다.
  15. 필요한 경우 글로브박스에 고객의 물건을 되돌려 놓습니다.