2024-07-18

Controller - High Voltage (Remove and Install)

Correction code 16301601 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Remove

  1. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  2. 12V/LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  3. 차량 절연 절차를 수행합니다. 참조 항목: Vehicle HV Disablement Procedure.
  4. 2열 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. 보조 베이 커버를 탈거합니다. 참조 항목: Cover - Ancillary Bay (Remove and Replace).
  6. 점화식 배터리 차단기를 탈거합니다. Pyrotechnic Battery Disconnect (Remove and Replace)을(를) 참조하십시오.
  7. 고전압 컨트롤러 커넥터에서 보조 베이 하네스를 연결 해제합니다.
  8. 힌지 트레이에 고전압 컨트롤러(HVC)를 고정하는 너트를 탈거한 다음 차량에서 컨트롤러를 탈거합니다.
    2 Nm (1.5 lbs-ft)
    그림 1. 5볼트 고전압 컨트롤러
    그림 2. 4볼트 고전압 컨트롤러
    그림 3. 3볼트 고전압 컨트롤러

Install

  1. 고전압 컨트롤러(HVC)를 보조 베이 내에 장착한 후, 고전압 컨트롤러(HVC)를 힌지 트레이에 고정하는 볼트를 장착합니다.
    2 Nm (1.5 lbs-ft)
  2. 고전압 컨트롤러 커넥터에서 보조 베이 하네스를 연결합니다.
  3. HV 컨트롤러를 들어 올려 퓨즈 절연체에 접근한 다음 퓨즈 절연체를 탈거합니다.
  4. 점화식 배터리 차단기를 장착합니다. 참조 항목: Pyrotechnic Battery Disconnect (Remove and Replace).
  5. 보조 베이 커버를 장착합니다. 참조 항목: Cover - Ancillary Bay (Remove and Replace).
  6. 12V/LV 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  7. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  8. 2열 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).