2025-09-11

Coolant Pump - HV Battery (Heat Pump) (Remove and Replace)

Correction code 18308522 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-07-09: 냉각수 펌프 유형을 구성하는 단계를 추가했습니다.
  • 2024-04-25: UI 루틴을 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
Informational PurposesAn informational icon, calling your attention
참고
냉각수 펌프를 두 번 교체한 경우 진행하기 전에 Toolbox 세션을 에스컬레이션합니다.

Torque Specifications

표 1. Torque Specifications: Coolant Pump - HV Battery (Heat Pump) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
HV 배터리 냉각수 펌프를 슈퍼매니폴드에 고정하는 볼트(4개)
1.8 Nm (1.3 lbs-ft)
  • Torx T20 소켓
  • 2인치 익스텐션
Reuse

Remove

  1. 차량을 2포스트 리프트에 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    차량이 충전 중이 아닌지 확인하십시오.
  2. 차량을 정비 모드로 전환합니다. 참조 항목: Service Mode.
  3. 실내 흡기 덕트를 탈거합니다. 참조 항목: 덕트 - 상단 - 실내 흡기(탈거 및 교체).
  4. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  5. 터치스크린에서 Service Mode > Thermal > Coolant System > Coolant Fill/Drain을 터치하고 Run을 선택하여 루틴이 완료될 때까지 기다립니다.
  6. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  7. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  8. 커넥터 잠금 장치를 분리한 다음 HV 배터리 냉각수 펌프 전기 커넥터를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    빨간색 탭을 누르지 마십시오. 빨간색 탭을 당겨 잠금 장치 체결을 해제한 다음 다시 당겨 커넥터를 분리하십시오.
  9. 냉각수 배출 용기를 배터리 냉각수 펌프 아래에 배치합니다.
  10. HV 배터리 냉각수 펌프를 슈퍼매니폴드에 고정하는 볼트(4개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 2인치 익스텐션
  11. 슈퍼매니폴드에서 HV 배터리 냉각수 펌프를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    두 개의 O링(내부 자주색, 외부 검정)이 모두 기존 펌프와 빠져 나가는지 확인합니다.

Install

  1. 장착하기 전에 두 개의 O링을 실리콘 O링 윤활제로 윤활합니다.
  2. HV 배터리 냉각수 펌프를 슈퍼매니폴드에 배치한 다음 볼트(4개)를 장착하고 손으로 조입니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 2인치 익스텐션
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터 위치를 기록하고 커넥터 탭이 위를 향하도록 냉각수 펌프를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    더 쉽게 장착할 수 있도록 냉각수 펌프와 함께 상단 오른쪽 볼트를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 펌프가 완전히 안착되었는지 확인합니다.
  3. HV 배터리 냉각수 펌프를 슈퍼매니폴드에 고정하는 볼트(4개)를 규격 토크로 조입니다.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 2인치 익스텐션
  4. HV 배터리 냉각수 펌프 전기 커넥터를 연결한 다음 커넥터 잠금 탭을 체결합니다.
  5. 차량 아래에서 냉각수 배출 용기를 치웁니다.
  6. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  7. 냉각 시스템 진공 보충을 수행합니다. 참조 항목: Cooling System (Vacuum Refill).
  8. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  9. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  10. 터치스크린에서 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Thermal > Stop Thermal Fill Drain을 탭하고 루틴이 완료될 때까지 기다립니다.
  11. 차량을 정비 모드 플러스로 전환합니다.
    1. 차량 Ops 모바일 앱에 VIN의 마지막 6자리를 입력합니다.
    2. 목록에서 차량을 선택합니다.
    3. 왼쪽으로 스와이프한 다음 Enable Service Mode Plus를 선택합니다.
  12. Thermal > Vehicle Configurations > coolantPumpType을 탭하여 현재 냉각수 펌프 구성을 검사합니다. 구성이 DUAL_MIX가 아닌 경우 DUAL_MIX로 변경합니다.
  13. Coolant System > Run Coolant Pumps Identification > Run을 탭하고 루틴을 통과하면 종료합니다.
  14. Coolant System > Coolant Purge > Run을 탭하고 루틴을 통과하면 종료합니다.
  15. 냉각수 수위를 검사하고 필요한 경우 보충합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수가 "Max" 선까지 채워졌는지 확인하십시오.
  16. 냉각수 보틀 캡을 장착합니다.
  17. 실내 흡기 덕트 어셈블리를 장착합니다. 참조 항목: 덕트 - 상단 - 실내 흡기(탈거 및 교체).
  18. 터치스크린에서 Exit Service Mode 버튼을 길게 눌러 정비 모드 플러스를 종료합니다.