2024-09-09

Hub - Rear - LH (Remove and Replace)

Correction code 31030702 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-01-19: EPB 정비 모드 참조를 업데이트했습니다.
  • 2023-11-30: 후면 하프샤프트 너트의 규격 토크 수치를 245Nm에서 300Nm으로 업데이트했습니다.
  • 2023-04-20: 절차를 수정했습니다.
  • 2023-05-25: 보충 목적 전용으로 전체 절차 비디오를 개요로 추가했습니다.
  • 2023-09-11: LH 후면 허브를 너클에 고정하는 볼트를 폐기하는 것에서 재사용하는 것으로 업데이트했습니다.
  • 2023-11-13: 허브 풀러 공구가 업데이트되어 브레이크 로터 볼트를 제거하는 단계 순서를 변경했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Remove

  1. 타이어에 비정상적인 마모가 있는지 검사합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    얼라인먼트가 필요함을 나타낼 수 있는 비정상적인 타이어 마모를 기록하십시오.
  2. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  3. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  4. EPB 정비 모드를 활성화합니다. 참조 항목: Parking Brake - Caliper - Rear - LH (Release).
  5. LH 후면 휠 중앙 캡이 장착되어 있는 경우 탈거합니다. 참조 항목: Cap - Wheel (Remove and Replace).
  6. LH 후면 휠 러그 너트를 풀되 아직은 휠을 탈거하지 마십시오. 참조 항목: Wheel Assembly (Remove and Install).
  7. LH 후면 하프샤프트 너트를 풉니다.
  8. LH 후면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  9. 주차 브레이크에서 전기 배선 하네스 커넥터를 연결 해제합니다.
  10. LH 후면 캘리퍼를 LH 후면 너클에 고정하는 볼트(2개)를 탈거하여 폐기합니다. 너클에서 캘리퍼를 탈거한 다음, 캘리퍼가 S자형 후크에 걸려 있도록 둡니다.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    초기 생산 차량에서는 러그 너트를 손으로 조여 로터를 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18
    • 래칫/토크 렌치
  11. 너트를 탈거하여 폐기하고 LH 하프샤프트를 허브 어셈블리에 고정하는 와셔를 탈거합니다.
  12. 허브 풀러를 LH 후면 로터에 장착한 다음 풀러 와셔(2개) 및 러그 너트(2개)를 로터 스터드에 장착하고 손으로 조입니다.
  13. 허브 풀러를 사용하여 허브 스플라인에서 하프샤프트를 헐거워지게 합니다.
  14. LH 후면 로터 스터드에서 러그 너트(x2)와 풀러 와셔(x2)를 탈거한 후 로터에서 허브 풀러를 탈거합니다.
  15. 허브에 브레이크 로터를 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    초기 생산 차량에는 로터를 고정하는 볼트가 장착되어 있지 않을 수 있습니다.
  16. 차량에서 LH 후면 브레이크 로터를 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    로터 표면을 아래로 배치하여 로터 페이스 손상을 방지합니다.
  17. LH 후면 허브를 너클에 고정하는 볼트(3개)를 탈거하고 차량에서 허브를 탈거합니다.
    85 Nm (62.7 lbs-ft)

Install

  1. 장착하기 전에 LH 후면 허브의 톤 링을 검사합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    톤 링에 손상 징후가 보이면 교체합니다.
    그림 1. 불량 톤 링
    그림 2. 양호한 톤 링
  2. 약 1그램의 Molykote M-77 윤활 페이스트를 LH 후륜 구동 장치 하프샤프트의 외측 허브 접착면에만 도포합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하프샤프트 스플라인에는 윤활제를 도포하지 마십시오. 실수로 스플라인에 윤활제를 도포한 경우 작업용 타월로 닦아냅니다.
    그림 3. 빨간색으로 강조 표시한 영역 윤활
  3. LH 후면 허브를 너클에 배치한 다음, 허브를 차량에 고정하는 볼트(3개)를 장착합니다.
    85 Nm (62.7 lbs-ft)
  4. LH 후면 하프샤프트를 LH 후면 허브 어셈블리에 고정하는 새 노트 및 와셔를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    너트는 이후 단계에서 토크로 조입니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32mm 딥 임팩트 소켓
    • 6인치 익스텐션
  5. LH 후면 브레이크 로터를 LH 후면 허브에 배치한 다음, 로터를 허브에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치
  6. LH 후면 캘리퍼 브래킷을 너클에 고정하는 새 볼트(2개)를 장착합니다.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18
    • 래칫/토크 렌치
  7. 전기 하네스를 LH 후면 브레이크 캘리퍼 커넥터에 연결합니다.
  8. LH 후면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  9. LH 후면 하프샤프트 너트를 장착합니다.
    300 Nm (221.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 6인치 익스텐션
    • 32mm 딥 임팩트 소켓
    • 래칫/토크 렌치
  10. LH 후면 휠 중앙 캡이 장착되어 있던 경우 장착합니다. 참조 항목: Cap - Wheel (Remove and Replace).
  11. 차량 터치스크린에서 주차 버튼을 길게 눌러 EPB 정비 모드를 해제합니다.
  12. LH 전면 도어를 닫고 LH 전면 창문을 올립니다.
  13. 리프트에서 차량을 내립니다.
  14. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See 얼라인먼트 요구 사항 - 서스펜션.