2020-12-16

Bumper Beam - Front (Remove and Replace)

Correction code 10011102 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Bumper Beam - Front (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
전면 범퍼 빔을 크러시 캔에 고정하는 볼트
75 Nm (55.3 lbs-ft)
  • 15mm 소켓
  • 3인치 익스텐션
교체

Remove

  1. 차량을 들어 올려서 지지합니다. Raise Vehicle - 2 Post Lift을(를) 참조하십시오.
  2. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  3. 실내 흡기 덕트를 탈거합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
  4. 후드 래치 커버를 탈거합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
  5. 후드 내 보관 유닛을 탈거합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
  6. 전면 페시아 어셈블리를 탈거합니다. Fascia - Front (Remove and Install)을(를) 참조하십시오.
  7. LH 전면 에어백 센서를 탈거합니다. Sensor - Impact Accelerometer - Front Bumper - LH (Remove and Replace)을(를) 참조하십시오.
  8. 중앙 전면 에어백 센서를 탈거합니다. Sensor - Impact Accelerometer - Front Bumper - Center (Remove and Replace)을(를) 참조하십시오.
  9. RH 전면 에어백 센서를 탈거합니다. Sensor - Impact Accelerometer - Front Bumper - LH (Remove and Replace)을(를) 참조하십시오.
  10. 에너지 업소버를 포함한 전면 범퍼를 크래시 캔에 고정하는 볼트를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15mm 소켓
    • 3인치 익스텐션
  11. 에너지 업소버를 포함한 전면 범퍼를 차량에서 주의하여 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    전면 범퍼를 비틀어 올릴 때 차체가 손상되지 않게 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    무반동 망치로 전방 범퍼를 가볍게 두드려 전방 범퍼의 탈거를 용이하게 합니다.
  12. 전방 범퍼에서 발포체를 탈거합니다.

Install

  1. 새 전방 범퍼 빔에 발포체를 장착합니다.
  2. 에너지 업소버를 포함한 전방 범퍼를 차량에 배치합니다.
  3. 에너지 업소버를 포함한 전방 범퍼를 LH 및 RH 크래시 캔에 고정하는 새 볼트를 장착합니다.
    75 Nm (55.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15mm 소켓
    • 3인치 익스텐션
  4. RH 전면 에어백 센서를 장착합니다. Sensor - Impact Accelerometer - Front Bumper - LH (Remove and Replace)을(를) 참조하십시오.
  5. 중앙 전면 에어백 센서를 장착합니다. Sensor - Impact Accelerometer - Front Bumper - Center (Remove and Replace)을(를) 참조하십시오.
  6. LH 전면 에어백 센서를 장착합니다. Sensor - Impact Accelerometer - Front Bumper - LH (Remove and Replace)을(를) 참조하십시오.
  7. 전면 페시아 어셈블리를 장착합니다. Fascia - Front (Remove and Install)을(를) 참조하십시오.
  8. 후드 내 보관 유닛을 장착합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
  9. 후드 래치 커버를 장착합니다. Cover - Hood Latch (Remove and Replace)을(를) 참조하십시오.
  10. 실내 흡기 덕트를 장착합니다. 덕트 - 상단 - 실내 흡기(탈거 및 교체)을(를) 참조하십시오.
  11. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  12. 리프트에서 차량을 내립니다.