2024-04-08

Cooling System (Partial Refill and Bleed)

Correction code 18300000 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

절차

  1. Toolbox 3이 설치된 노트북을 차량에 연결합니다.
  2. 검색 필드에 “열[thermal]”을 입력합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    “작업[actions]”이 아직 선택되지 않은 경우 선택합니다.
  3. PROC_VCFRONT_X_THERMAL-FILL-DRAINvia Toolbox: (link) 옆에 있는 play 버튼을 클릭한 다음, Run을 선택합니다.
  4. 슈퍼/냉각수 보틀에서 캡을 탈거합니다.
    그림 1. 슈퍼보틀이 있는 Model 3(히트 펌프 이외), 명확한 이해를 위해 다른 구성품은 제거됨
    그림 2. 냉각수 보틀이 있는 Model Y, Model 3(히트 펌프)도 유사함. 명확한 이해를 위해 다른 구성품은 제거됨
  5. 액체 수위가 MAX 선(히트 펌프 차량) 또는 MAX 선 위 약 6mm(히트 펌프 이외 차량)에 있도록 냉각수를 슈퍼/냉각수보틀에 추가합니다.
  6. 검색 필드에 “vcfront”를 입력합니다.
  7. TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    옆에 있는 play 버튼을 클릭한 다음, Run을 선택합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    드라이브 레일이 꺼져 있는지 확인하십시오. 구동 레일을 켜면 절차가 중단됩니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    루틴이 실행 중인 동안 슈퍼/냉각수 보틀을 모니터링하고 필요에 따라 냉각수를 추가하여 오일 수위를 NOM과 MAX 사이로 유지합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    테스트에 약 10분이 걸립니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    테스트 속도는 3,500~6,500RPM이며 PT 열 탭에서 확인할 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    속도가 7,000RPM 수준으로 유지되면 이 절차를 다시 수행합니다.
  8. 히트 펌프 차량만 해당: 공기 배출 루틴이 완료된 후 냉각수 보틀 오일 수위를 검사하고 냉각수를 MAX 선까지 추가합니다.
  9. 히트 펌프 이외 차량만 해당: 공기 배출 루틴이 완료될 후 슈퍼보틀 오일 수위를 검사하고 냉각수를 MAX 선 약 6mm(0.25인치)까지 추가합니다.
  10. 슈퍼/냉각수 보틀에 캡을 장착합니다.

Install

Installation procedure is the reverse of removal.