2024-05-30

Door - Front - LH (Remove and Install)

Correction code 10106001 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  2. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  3. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  4. LH 계기판 엔드캡을 탈거합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  5. 중간 A필러 트림 패널을 탈거합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  6. LH 하단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. LH 전면 도어 전기 커넥터를 LH 차체 컨트롤러 모듈에서 연결 해제합니다.
  8. LH 차체 컨트롤러 모듈에서 전기 하네스 클립을 분리합니다.
  9. 그로밋을 분리한 후, A필러 벌크헤드를 통해 LH 도어 전기 하네스를 누릅니다.
  10. LH 전면 도어 체크 스트랩을 A필러에 고정하는 볼트를 탈거합니다.
    24 Nm (17.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    도어 체크의 볼트를 풀면 도어가 개방 한계를 넘어 제한 없이 열립니다.
  11. 테이프를 이용해 LH 전면 도어의 도어 힌지 장착 위치를 표시합니다.
  12. 힌지 볼트를 느슨하게 푼 후, 각 힌지의 하단 볼트를 탈거합니다.
    24 Nm (17.7 lbs-ft)
  13. 각 힌지의 상단 볼트를 일부만 풀고, 보조 작업자와 함께 LH 전면 도어를 차량에서 들어 올립니다.

Install

Informational PurposesAn informational icon, calling your attention
TIp
전면 도어를 정렬하는 방법에 대한 지침은 전면 도어 정렬을(를) 참조하십시오.

Installation procedure is the reverse of removal, except for the following:

도어를 힌지에 놓아서 하단 볼트를 장착할 수 있도록 도어의 각 힌지의 상단 볼트를 부분적으로 조입니다.