2025-09-30

Seat Assembly - 1st Row - LH (Remove and Replace)

Correction code 13040102 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.
Informational PurposesAn informational icon, calling your attention
참고
전면 시트에는 에어백과 프리텐셔너가 포함되어 있으므로 적절하게 폐기해야 합니다. 자세한 내용은 전면 시트 에어백 탈거 및 폐기을(를) 참조하세요. 교정 코드 20010707을 사용하여 해당 작업에 관해 기록합니다. 전면 시트 에어백 및 프리텐셔너를 재사용이 불가능한 방식으로 탈거 및 폐기하는 작업 시간은 전면 시트의 탈거 및 교체 작업 시간에 반영되지 않습니다.
Informational PurposesAn informational icon, calling your attention
참고
1열 LH 시트에 대해 설명했지만 1열 RH 시트에 대한 절차도 동일합니다. 이 절차는 LHD 및 RHD 차량의 운전석 시트 및 동승석 시트에 사용할 수 있습니다.
  • 1133787-00-A 키, 안전벨트 해제, Model 3
  • 1082447-07-A Torx Plus T45
  • 2024-12-04: Tesla 미니 틸트 모터가 장착된 전면 시트 어셈블리에 대한 구성 정보를 추가했습니다.
  • 2023-08-01: 단계를 재구성했습니다.
  • 2023-07-03: 전면 및 후면 시트 트랙 커버 탈거 및 장착 단계를 추가했습니다.

Torque Specifications

표 1. Torque Specifications: Seat Assembly - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
전면 시트를 차체에 고정하는 볼트
33.5 Nm (24.7 lbs-ft)
  • Trox Plus T45 소켓
  • 3/8인치 표준 플렉스 헤드 래칫
  • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
Replace 볼트가 패치되어 있음

Remove

  1. 모든 도어를 열고 창문을 모두 내립니다.
  2. 전면 동승석 시트를 서비스하는 경우:
    1. 차량을 정비 모드로 전환합니다. 참조 항목: Service Mode.
    2. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
    3. 차량 소프트웨어를 다시 설치합니다. 참조 항목: Software Reinstall - Touchscreen.
  3. LH 중간 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  4. LH 하단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  5. LH 전면 시트를 뒤로 이동합니다.
  6. 운전석 시트 트랙 전면 커버를 탈거합니다. 참조 항목: Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  7. 1열 LH 시트의 전면을 차체에 고정하는 볼트(2개)를 탈거하여 폐기합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use the torchless heat induction tool to ease the removal of patch bolts, if necessary.
  8. LH 전면 시트를 앞으로 움직입니다.
  9. 안전벨트 릴리스 키(1133787-00-A)를 안전벨트 프리텐셔너 커플링에 삽입하여 안전벨트를 프리텐셔너에서 분리합니다.
  10. 운전석 시트 트랙 후면 커버를 탈거합니다. 참조 항목: Cover - Rear - Seat Track - 1st Row Seat (Remove and Replace).
  11. 1열 LH 시트의 후면을 차체에 고정하는 볼트(2개)를 탈거하여 폐기합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use the torchless heat induction tool to ease the removal of patch bolts, if necessary.
  12. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  13. LH 전면 시트를 트랙의 가운데로 배치하고 시트 등받이를 수직 위치로 배치합니다.
  14. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  15. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  16. LH 차체 컨트롤러에서 시트 전기 하네스 커넥터를 연결 해제합니다.
  17. 시트 전기 하네스를 차체에 고정하는 클립을 풀어줍니다.
  18. 보조 작업자와 함께 차량에서 시트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    시트를 들어 올리고 시트 등받이를 기울인 다음, 쿠션을 도어 쪽으로 돌리고 차량에서 시트를 탈거하되 쿠션을 먼저 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    If discarding the entire seat, Service Centers must remove the seat-mounted airbag and pre-tensioner (if present) before discarding the seat. Follow local Environmental Health and Safety (EH&S) best practices to dispose of the airbag and pre-tensioner (for example, place the airbag and pre-tensioner into the appropriate hazardous waste receptacles located in the Service Center). Refer to 전면 시트 에어백 탈거 및 폐기 for instructions, and use Correction Code 20010707 to document the labor; the labor time for destructively removing and disposing of the front seat airbag (and pre-tensioner, if equipped) is not reflected in the front seat removal and replacement labor time.

Install

  1. 보조 작업자와 함께 차량에 시트를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    헤드레스트를 도어 입구 쪽으로 향하고, 시트 쿠션을 차량 후면으로 향하게 하여 시트를 옆으로 들어 올립니다. 헤드레스트를 도어 안으로 움직이고, 시트 쿠션이 뒤따릅니다. 쿠션이 위로 향하도록 시트를 방향을 돌리고 시트를 카펫 위에 내린 다음 시트 등받이를 수직으로 돌립니다.
  2. 시트 전기 하네스를 차체에 고정하는 클립을 조입니다.
  3. LH 차체 컨트롤러에 시트 전기 하네스 커넥터를 연결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    시트 전기 하네스 커넥터에서 이물질을 모두 제거하고 커넥터를 차체 컨트롤러에 단단히 누른 다음, 커넥터 잠금 장치를 체결합니다.
  4. 12V 하네스 브래킷과 차체 사이에 여분의 하네스 길이를 끼워 넣습니다.
  5. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  7. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace)
  8. 시트를 뒤로 끝까지 이동합니다.
  9. 새 볼트(2개)를 장착하여 1열 LH 시트의 전면을 차체에 고정합니다.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 규격 토크로 조입니다.
  10. 운전석 시트 트랙 전면 커버를 장착합니다. 참조 항목: Cover - Front - Seat Track - 1st Row Seat (Remove and Replace).
  11. 시트를 앞으로 끝까지 이동합니다.
  12. 새 볼트(2개)를 장착하여 1열 LH 시트의 후면을 차체에 고정합니다.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 규격 토크로 조입니다.
  13. 운전석 시트 트랙 후면 커버를 장착합니다. 참조 항목: Cover - Rear - Seat Track - 1st Row Seat (Remove and Replace).
  14. 안전벨트 프리텐셔너 커플링에 안전 벨트를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    안전벨트 프리텐셔너를 안전벨트 프리텐셔너 커플링에 재장착한 후, 안전벨트를 당겨 안전벨트와 프리텐셔너가 단단히 체결되어 있는지 확인합니다.
  15. LH 하단 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  16. 2024년 6월 이후 조달된 교체용 전면 시트 어셈블리와 시트 쿠션 프레임 어셈블리에는 새롭게 설계된 Tesla "미니 틸트" 모터가 장착되어 있으며, 이러한 부품(또는 틸트 모터 자체)을 교체하려면 구성을 변경해야 할 수 있습니다. 표의 구성 정보를 검토하고 구성 업데이트가 필요한 경우 다음 하위 단계를 수행합니다.
    1. Infotainment DashboardVehicle Configuration 섹션에 액세스합니다. 참조 항목: 게이트웨이 구성(표시 및 변경).
    2. 표에 설명된 틸트 모터의 조합에 따라 cfg_frontSeattype을 업데이트합니다.
  17. 운전석 시트를 서비스하는 경우:
    1. 차량 터치스크린을 사용하여 차량을 정비 모드로 설정합니다. 참조 항목: Service Mode.
    2. 차량 소프트웨어를 다시 설치합니다. 참조 항목: Software Reinstall - Touchscreen.
    3. 차량 터치스크린에서 컨트롤 > 정비 > 운전석 시트, 스티어링 및 미러 보정 > 시작을 터치합니다.
    4. 정비 모드를 종료합니다. 참조 항목: Service Mode.
  18. 북미 또는 대한민국 차량의 전면 동승석 시트를 정비하는 경우:
    1. 구성 변경이 필요한지 확인하기 위해 부품 카탈로그를 참조합니다.
    2. 보정을 시작하기 전에 전면 동승석 시트에서 모든 물체를 제거하십시오.
    3. 차량 소프트웨어를 다시 설치합니다. 참조 항목: Software Reinstall - Touchscreen.
    4. 보정을 시작하기 전에 전면 동승석 시트에서 모든 물체를 제거하십시오.
    5. Toolbox 3가 설치된 노트북을 차량에 로컬로 연결합니다. 참조 항목: Toolbox 3(연결 및 연결 해제).
    6. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
    7. Toolbox에서 Actions 탭을 클릭한 다음 "OCS"를 검색합니다.
    8. PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration 루틴을 Run합니다.
    9. Actions 탭을 클릭한 다음 "Seat calibration"을 검색합니다.
    10. PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate 루틴을 Run합니다.
    11. Toolbox를 연결 해제하고 차량에서 노트북을 탈거합니다.
  19. 시트를 원래 위치로 이동합니다.
  20. 모든 창문을 올리고 도어를 모두 닫습니다.