2022-04-24

Diffuser - Rear Fascia (Remove and Replace)

Correction code 12030802 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. 토크 규격: Diffuser - Rear Fascia (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
후면 페시아 디퓨저를 차량에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 소켓
  • 2인치 익스텐션
Reuse
후면 페시아 디퓨저를 후면 페시아의 외측 가장자리에 고정하는 볼트
3 Nm (2.2 lbs-ft)
  • 10mm 소켓
Reuse
후면 페시아 디퓨저를 후면 페시아의 내부에 고정하는 볼트
3 Nm (2.2 lbs-ft)
  • 10mm 소켓
Reuse

Remove

  1. 차량을 들어 올려서 지지합니다. Raise Vehicle - 2 Post Lift을(를) 참조하십시오.
  2. LH 후면 부분 및 RH 후면 휠 라이너의 차체에 고정하는 클립을 탈거합니다.
  3. 중앙 에어로 실드 패널을 탈거합니다. Panel - Aero Shield - Rear (Remove and Replace)을(를) 참조하십시오.
  4. 패스너 커버를 탈거한 다음 후면 페시아 디퓨저를 차량에 고정하는 볼트를 탈거합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    신형 차량에는 전면 및 중간 볼트가 장착되어 있지 않습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
  5. 후면 페시아 디퓨저를 후면 페시아의 외측 가장자리에 고정하는 볼트를 탈거합니다.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  6. 후면 페시아 디퓨저를 후면 페시아의 내부에 고정하는 볼트를 탈거합니다.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    느슨해진 후면 페시아 디퓨저를 통해 이 볼트에 접근합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  7. 후면 페시아 디퓨저를 휴면 페시아에 고정하는 탭을 분리한 후, 디퓨저를 탈거합니다.

Install

Installation procedure is the reverse of removal.