2025-09-11

Fluid Coupling (90 Degrees) - Front Drive Unit (Remove and Replace)

Correction code 39014012 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 전면 서브프레임 어셈블리를 탈거합니다. 참조 항목: Subframe Assembly - Front (Dual Motor) (Remove and Install).
  2. 전륜 구동장치 인입 호스를 90도 오일 커플링에 고정하는 클립을 분리한 다음 호스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    필요한 경우 접이식 깔때기를 사용합니다.
  3. LH 전륜 구동 장치 마운트를 전륜 구동 장치에 고정하는 볼트를 탈거하여 폐기한 다음 전륜 구동 장치에서 마운트를 탈거합니다.
  4. 90도 오일 커플링을 구동 인버터(DI)에 고정하는 패스너를 탈거하여 폐기한 다음 인버터에서 90도 오일 커플링을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

  1. 오일 커플링 O링을 냉각수로 윤활합니다.
  2. 90도 오일 커플링을 구동 인버터(DI)에 배치한 다음 새 패스너를 장착합니다.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  3. 냉각수 압력 테스트를 수행합니다:
    1. 냉각수 압력 테스트 플러그 어댑터를 직선 오일 커플링에 장착합니다.
    2. 냉각수 압력 어댑터를 90도 오일 커플링에 장착합니다.
    3. 냉각수 압력 어댑터를 압축 공기 라인에 고정합니다.
    4. 압력을 50psi로 설정한 다음 압력 조절기의 밸브를 천천히 엽니다. 압력이 50psi에 도달할 때까지 기다립니다.
    5. 압력이 안정될 때까지 15초간 기다린 다음 압력 측정값을 기록합니다.
    6. 12초간 더 기다린 다음 측정값을 기록합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      압력이 0.1psi 이상 떨어지지 않았어야 합니다. 압력 테스트가 실패하는 경우 오일 커플링이 완전히 안착했는지 확인한 다음 압력 테스트를 다시 실행합니다.
    7. 인버터에서 냉각수 압력 테스트 구성품을 탈거합니다.
  4. LH 전륜 구동 장치 마운트를 전륜 구동 장치에 장착한 다음 마운트를 전륜 구동 장치에 고정하는 새 볼트를 장착합니다.
    35 Nm (25.8 lbs-ft) + 55 degrees
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 PN: 1111864-00-B
  5. 전륜 구동장치 인입 호스를 90도 오일 커플링에 장착합니다.
  6. 전면 서브프레임 어셈블리를 장착합니다. 참조 항목: Subframe Assembly - Front (Dual Motor) (Remove and Install).