2025-04-11

Retractor - Seatbelt - 1st Row - LH (Remove and Replace)

Correction code 20054102 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1133787-00-A 키, 안전벨트 해제, Model 3

Torque Specifications

표 1. Torque Specifications: Retractor - Seatbelt - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
상단 D링을 조절식 상부 루프에 고정하는 패치 볼트
30 Nm (22.1 lbs-ft)
  • Torx T50 소켓
  • 3/8인치 표준 래칫
  • 3/8인치 토크 렌치(장착 전용)
  • 3인치 익스텐션
Replace
안전벨트 웹 가이드를 B필러에 고정하는 볼트
5 Nm (3.7 lbs-ft)
  • 8mm 소켓
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
Replace
안전벨트 리트랙터를 B필러 베이스에 고정하는 패치볼트
40 Nm (29.5 lbs-ft)
  • 13mm 12 포인트 딥소켓
  • 3/8인치 표준 래칫
  • 3/8인치 토크 렌치(장착 전용)
Replace

Remove

  1. LH 계기판 엔드캡을 탈거합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  2. LH 중간 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  3. LH 하단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  4. 안전벨트 릴리스 키(1133787-00-A)를 안전벨트 프리텐셔너 커플링에 삽입하여 안전벨트를 프리텐셔너에서 분리합니다.
  5. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  6. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  7. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  8. LH 2열 시트 사이드 볼스터를 탈거합니다. 참조 항목: Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  9. LH 후면 실 패널 트림을 탈거합니다. 참조 항목: Trim - Sill Panel - Rear - LH (Remove and Replace).
  10. LH 상단 B필러 트림을 차량에 고정하는 클립을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    LH 상단 B필러 트림 하단부의 클립을 먼저 분리한 다음 트림 상단부의 클립을 분리합니다.
  11. 안전벨트를 LH 상단 B필러 트림의 구멍을 통해 바깥쪽으로 민 다음 트림을 한쪽으로 치워둡니다.
  12. LH 하단 B필러 트림을 탈거합니다. 참조 항목: Trim - B-Pillar - Lower - LH (Remove and Replace).
  13. 안전벨트 웨빙 가이드를 B필러에 고정하는 볼트를 탈거한 다음 B필러에서 가이드를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  14. 상단 D링을 상단 루프에 고정하는 패치볼트를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
    • 3인치 익스텐션
  15. 안전벨트 리트랙터를 B필러 베이스에 고정하는 패치볼트를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 12 포인트 딥소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
  16. 안전벨트 리트랙터 커넥터(2개)에서 전기 하네스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터에 더 쉽게 접근하기 위해 먼저 B필러에서 리트랙터를 탈거할 수 있습니다.
  17. 차량에서 LH 전면 안전벨트를 탈거합니다.

Install

  1. 전기 하네스를 안전벨트 리트랙터 커넥터(2개)에 연결한 다음 리트랙터를 B필러에 배치시킵니다.
  2. 안전벨트 리트랙터를 B필러 베이스에 고정하는 새 패치 볼트를 장착합니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 12 포인트 딥소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
  3. 상단 D링을 상단 루프에 고정하는 새 패치 볼트를 장착합니다.
    30 Nm (22.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
    • 3인치 익스텐션
  4. 안전벨트 웨빙 가이드를 B필러에 장착한 후, 가이드를 B필러에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  5. 안전벨트를 LH 상단 B필러 트림의 구멍을 통해 밀어 넣습니다.
  6. LH 하단 B필러 트림을 장착합니다. 참조 항목: Trim - B-Pillar - Lower - LH (Remove and Replace).
  7. LH 상단 B필러 트림을 차량에 고정하는 클립을 조입니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    LH 상단 B필러 트림 상단부의 클립을 먼저 조인 후 트림 하단부의 클립을 조입니다.
  8. LH 후면 실 패널 트림을 장착합니다. 참조 항목: Trim - Sill Panel - Rear - LH (Remove and Replace).
  9. LH 2열 시트 사이드 볼스터를 장착합니다. 참조 항목: Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  10. 12V 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  11. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  12. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  13. LH 전면 안전벨트 리트랙터 커플링을 LH 전면 시트 프리텐셔너에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    밀고 당기기 검사를 수행하여 프리텐셔너와 커플링이 완전히 체결되었는지 확인합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  14. LH 하단 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  15. LH 중간 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Middle - LH (Remove and Replace).
  16. LH 계기판 엔드캡을 장착합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).