2025-09-11

Brake Caliper - Front - LH (Remove and Replace)

Correction code 33010302 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-06-06: 토크 규격표를 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
Informational PurposesAn informational icon, calling your attention
참고
사용한 브레이크 오일은 현지 환경 규정에 따라 폐기합니다.
Informational PurposesAn informational icon, calling your attention
참고
이 절차는 Model 3 기본 모델 및 스포츠 브레이크 캘리퍼 모두에 적용합니다.

Torque Specifications

표 1. 토크 규격: Brake Caliper - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 전면 브레이크 캘리퍼를 LH 전면 너클에 고정하는 볼트
94 Nm (69.3 lbs-ft)
  • 코드리스 래칫/임팩트 드라이버
  • 3/8인치 ~ ½인치 어댑터
  • 외부 Torx E18
  • 래칫/토크 렌치
Replace 1088969-00-B

Remove

  1. 차량을 2포스트 리프트에 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    차량이 충전 중이 아닌지 확인하십시오.
  2. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  3. LH 전면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  4. LH 전면 자운스 호스를 탈거합니다. 참조 항목: Brake Hose - Flexible - Front - LH (Remove and Replace).
  5. LH 전면 브레이크 캘리퍼를 LH 전면 너클에 고정하는 볼트를 탈거하여 폐기한 다음 차량에서 캘리퍼를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 코드리스 래칫/임팩트 드라이버
    • 3/8인치 ~ ½인치 어댑터
    • 외부 Torx E18
    • 래칫/토크 렌치

Install

  1. LH 전면 브레이크 캘리퍼를 LH 전면 너클에 장착한 다음 캘리퍼를 너클에 고정하는 새 볼트를 장착하고.
    94 Nm (69.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 코드리스 래칫/임팩트 드라이버
    • 3/8인치 ~ ½인치 어댑터
    • 외부 Torx E18
    • 래칫/토크 렌치
  2. 새 LH 전면 자운스 호스를 장착합니다. 참조 항목: Brake Hose - Flexible - Front - LH (Remove and Replace).
  3. 차량을 낮춥니다.
  4. LH 전면 브레이크 캘리퍼에 대해 블리딩 절차를 수행합니다. 참조 항목: Brake Fluid Bleed - One Caliper.
  5. LH 전륜 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  6. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  7. 다음 중 하나를 선택하십시오.
    • 브레이크 패드를 브레이크 캘리퍼로 교체하지 않은 경우 다음 단계로 이동한 후 이 절차를 완료합니다.
    • 브레이크 패드를 브레이크 캘리퍼로 교체한 경우 다음 단계로 이동합니다. 8
  8. Perform a road test and burnish the brake pads. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure proper brake pedal feel and brake performance.
    Informational PurposesAn informational icon, calling your attention
    참고
    Add correction code 33013000 as a separate activity to the SV.