2025-06-27

Brake Pad Kit - Rear (Base Brakes) (Remove and Replace)

Correction code 33010802 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1134520-00-A 키트, EPB 해제, 휴대용
  • 1129348-00-A XP-10 전원 공급, XP-10
  • 2024-05-28: 참조 및 주의 사항을 업데이트했습니다.
Informational PurposesAn informational icon, calling your attention
참고
자세한 브레이크 규격은 브레이크을(를) 참조하십시오.

Torque Specifications

표 1. Torque Specifications: Brake Pad Kit - Rear (Base Brakes) (Remove and Replace)
Description Torque Value Reuse/Replace Notes
LH 후면 브레이크 캘리퍼에서 LH 후면 브레이크 캘리퍼 브래킷
26.5 Nm (19.5 lbs-ft)
  • 14mm 소켓
Reuse

Remove

  1. LH 후면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. LH 후면 브레이크 캘리퍼를 LH 후면 브레이크 캘리퍼 브래킷에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 14mm 소켓
  4. 브레이크 캘리퍼 S자형 고리를 사용하여 LH 후면 브레이크 캘리퍼를 차체에 겁니다.
  5. LH 후면 브레이크 캘리퍼 브래킷에서 브레이크 패드를 탈거합니다.
  6. LH 후면 브레이크 캘리퍼 브래킷에서 캘리퍼 받침대 클립을 탈거합니다.
  7. 1~10단계를 반복하여 RH 후면 브레이크 패드를 탈거합니다.

Install

  1. 니들 노즈 플라이어를 사용하여 후면 브레이크 캘리퍼 피스톤 페이스가 12시 위치와 6시 위치에 있도록 합니다.
  2. 캘리퍼 받침대 클립을 장착합니다.
  3. 받침대 클립에 Silaramic 윤활제를 고르게 도포합니다.
  4. 브레이크 패드를 LH 후면 브레이크 캘리퍼 브래킷에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    설치 중 브레이크 패드를 브레이크 로터를 향해 누릅니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    더 많은 공간이 필요한 경우 캘리퍼 스프레더 도구를 사용하여 캘리퍼 피스톤을 다시 캘리퍼 안으로 밀어 넣습니다.
  5. LH 후면 브레이크 캘리퍼를 LH 후면 브레이크 캘리퍼 브래킷에 고정하는 볼트를 장착합니다.
    26.5 Nm (19.5 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    To prevent damage to the flexible brake hose, make sure that the brake hose is not twisted and can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 14mm 소켓
  6. LH 후면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  7. 이전 모든 장착 단계를 반복하여 RH 후면 브레이크 패드를 장착합니다.
  8. 터치스크린에서 주차 버튼을 터치하여 주체 브레이크를 적용합니다.
  9. 터치스크린에서 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Chassis > Brakes > EPB Service Mode를 탭하고 EPB Selection 드롭다운 목록에서 Both를 선택한 다음 Action Selection 드롭다운 목록에서 Stop을 선택합니다. Run을 클릭하여 루틴이 완료될 때까지 기다립니다.
  10. 정비 모드를 종료합니다. 참조 항목: Service Mode.
  11. 페달이 단단하게 느껴질 때까지 브레이크 페달을 밟아 패드를 브레이크 로터에 안착시킵니다.
  12. 브레이크액의 수위를 확인하고 필요한 경우 브레이크액 저장 탱크를 가득 채웁니다.
  13. Perform a road test and burnish the brake pads. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure proper brake pedal feel and brake performance.
    Informational PurposesAn informational icon, calling your attention
    참고
    Add correction code 33013000 as a separate activity to the SV.