2025-09-23
성에 제거 커버 - 계기판 - LH(탈거 및 교체)
교정 코드
14051502 1.68
바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.
참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오.
바고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.
- Open both front doors
- Lower both front windows
- Move LH front seat backward
- Move RH front seat backward
-
Clear DAS Calibration through UI
참고Controls > Service > Camera Calibration, Select Clear Calibration, Verify calibration was cleared successfully, Wait for prompt to disappear automatically before continuing, Calibration in Progress message and progress icon will appear during the next drive cycle
-
Open hood
참고Press "Open" button on the touchscreen to release the latch, Lift the lid manually
-
Remove rear apron
참고12x clips, Only store rear apron visible face upwards
-
Remove cabin intake upper duct assembly
참고4x clips, Heat pump vehicles have 3x clips
-
Remove closeout panel from frunk assembly
참고4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Grab closeout panel from bottom then pull it upward to release clips, Disconnect the switch
- Remove frunk assembly carpet
-
Remove bolts securing frunk assembly
참고7x bolts, 10mm, 5 Nm, Lift up RBN covers to access upper fasteners, Newer vehicles may not be equipped with covers
-
Remove frunk assembly from vehicle
참고12x clips, Replace any clips if broken or missing, Number of clips may vary on older vehicles
-
Remove LH wiper arm nut cover
참고1x cover
-
Disconnect washer hose from LH wiper arm to Y-tube fitting and release washer hose clips
참고2x clips, 1x hose
-
Remove the nut securing the LH wiper arm to wiper module
참고1x nut, 15mm, 25 Nm
- Remove LH wiper arm and hose assembly from vehicle
-
Remove RH wiper arm nut cover
참고1x cover
-
Disconnect washer hose from RH wiper arm to Y-tube fitting and release washer hose clips
참고2x clips, 1x hose
-
Remove the nut securing the RH wiper arm to wiper module
참고1x nut, 15mm, 25 Nm
- Remove RH wiper arm and hose assembly from vehicle
-
Remove the LH shock tower cover
참고2x push clips
-
Remove the RH shock tower cover
참고2x push clips
-
Release cowl screen from windshield and remove from vehicle
참고2x push clips, 6x clips
-
Disconnect windshield heater connector
참고1x connector
- Secure heater harness onto windshield
-
Remove lower quad camera cover
참고4x tabs, Press on the side of the cover with a trim tool to release some of the tabs
-
Remove tether from lower quad camera cover
참고2x tabs, Depress tabs to remove tether
-
Remove rear view mirror
참고Turn mirror counterclockwise to remove, do not twist by holding the mirror itself, it will separate from the stalk, twist from the stalk connecting the mirror to the mount
-
Disconnect rear view mirror connector
참고1x connector
-
Remove quad camera upper cover
참고4x clips, 1x connector, Pull the cover down to remove and then disconnect interior camera
-
Remove triple camera hood
참고2x patch screws, T10, 1 Nm, 2x alignment pins, Discard fasteners after removal
-
Remove triple camera assembly
참고4x screws, T10, 1 Nm
-
Disconnect humidity and temperature sensor harness connector
참고1x connector
-
Remove screw securing windshield harness to windshield bracket and move harness aside
참고1x screw, T10, 1 Nm
-
Remove GPS/GNSS antenna from bracket
참고1x screw, T10, 1 Nm, 2x tabs, Slide antenna to LH side to release from bracket
-
Separate harness track from windshield
참고Located above RH visor under headliner, Slide equalizer up against track and carefully tap equalizer to separate from windshield
- Prepare WRD Spider 3 glass removal kit
-
Secure line to starter tool and push tool through urethane at lower RH side of winshield
참고Use the guard to prevent damage to dash pad while using starter tool
-
Release line from starter tool and wrap line around exterior of windshield
참고Pull line away from starter tool, Ensure enough length is pulled through, Wrap spider line up and around the exterior of windshield, Verify the line sits underneath the glass
-
Attach anchor point to exterior of windshield and secure line
참고Attach line to anchor once fully wrapped around windshield, Place anchor near starting point of the handle tool
-
Secure interior side of line to the spider cutting tool
참고Follow instructions on spider tool, Feed line through opening of the cutting tool and tie a knot to secure in place, If spindle is not turned the proper direction the cutting tool will be damaged
-
Secure spider cutting tool to interior side of windshield
참고Note orientation of the cutting line, Make sure line warps over large pully and holds at a 90 degree angle
- Secure angle driver to electric drill
-
Turn the spindle on the cutting tool with the drill to start removing the windshield
참고Move the cutting tool as needed keeping the line close to a 90 degree angle, When passing vin plate use guard to guide line over vin to prevent damage
- Attach suction cups to windshield on both sides
-
Lift up to remove windshield from vehicle
참고Recommend assistance, use caution with windshield harness, Partially close hood for clearance
-
Place windshield on support stand
참고Recommend assistance
- Remove old urethane from windshield
- Remove sealing strip from windshield
-
Clean urethane residue from windshield
참고Allow 1 minute dry time
- Remove old urethane from vehicle
- Remove IP cowl foam
-
Remove LH defrost cover
참고11x tabs
-
Install LH defrost cover
참고11x tabs, Secure 2x middle tabs first then secure tabs from middle to LH side of IP, Make sure cover is flush with speaker grill
- Install IP cowl foam
-
Install sealing strip onto windshield
참고Follow windshield alignment marks at upper corners of glass, Start from one corner and peel tape as you apply inch by inch to ensure proper fitment
-
Measure resistance of heater grid to check continuity
참고Measured at ambient temperature, Tolerance 5.6Ω+/-10%, Check from pin 1 to pin 2 on X304, If resistance is outside tolerance then replace windshield
-
Perform windshield dry fit
참고Note any locations where net pads need to be adjusted
-
Perform any net pad adjustments for windshield
참고Add or remove to adjust flush condition if necessary, No time recorded as it was not necessary during validation
-
Wipe urethane path on vehicle
참고Allow 1 minute dry time
-
Apply urethane primer to windshield and vehicle body along old urethane path
참고Make sure to add primer over any areas that were scratched during windshield removal, Allow primer to dry for 2 minutes before applying urethane
-
Prepare caulking gun and urethane
참고Opening must be 8mm wide and 13mm tall
- Apply urethane to windshield following primer path
-
Install windshield onto vehicle
참고Recommend assistance
-
Check gaps and flushness to vehicle before fully seating windshield
참고Adjust glass as needed
- Apply tape to secure windshield to body while urethane cures
- Remove suction cups from windshield
-
Install GPS/GNSS antenna onto bracket
참고1x screw, T10, 1 Nm, 2x tabs, Slide antenna towards RH side to secure tabs
-
Install screw securing windshield harness to windshield bracket
참고1x screw, T10, 1 Nm, Make sure harness is routed inside of bracket
-
Connect humidity and temperature sensor harness connector
참고1x connector
-
Secure trilobe and triple camera assembly onto windshield bracket
참고4x screws, T10, 1 Nm
-
Install triple camera hood
참고2x patch screws, T10, 1 Nm, 2x alignment pins, Install new fasteners
-
Install quad camera upper cover
참고4x clips, 1x connector, Connect interior camera then push the cover up to secure
-
Connect rear view mirror connector
참고1x connector
-
Install rear view mirror
참고Turn mirror clockwise to install, do not twist by holding the mirror itself, it will separate from the stalk, twist from the stalk connecting the mirror to the mount
-
Install tether onto lower quad camera cover
참고2x tabs
-
Install quad camera lower cover
참고4x tabs, Install the tabs closest to the rearview mirror assembly and push the cover up to secure
- Move RH front seat to original position
- Move LH front seat to original position
- Release heater harness from windshield
-
Connect windshield heater connector
참고1x connector
-
Install cowl screen assembly
참고2x push clips, 6x clips
-
Install the RH shock tower cover
참고2x push clips
-
Install the LH shock tower cover
참고2x push clips
- Install the RH wiper arm and hose assembly onto vehicle
-
Install the nut securing the RH wiper arm to wiper module
참고1x nut, 15mm, 25 Nm, Make sure the wiper tip is aligned between the two indicators at corner of windshield
-
Connect washer hose from RH wiper arm to Y-tube fitting and secure washer hose clips
참고2x clips, 1x hose
-
Install RH wiper arm nut cover
참고1x cover
-
Install LH wiper arm and hose assembly onto vehicle
참고The washer hose shall be routed over the arm pivot joint, not under
-
Install the nut securing the LH wiper arm to wiper module
참고1x nut, 15mm, 25 Nm, Make sure the wiper tip is aligned between the two indicators at windshield
-
Connect washer hose from LH wiper arm to Y-tube fitting and secure washer hose clips
참고2x clips, 1x hose
-
Install LH wiper arm nut cover
참고1x cover
-
Install frunk assembly to vehicle
참고12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles
-
Install bolts securing frunk assembly
참고7x bolts, 10mm, 5 Nm, Lower RBN covers after installing upper fasteners, Newer vehicles may not be equipped with covers
- Install frunk assembly carpet
-
Install frunk close out panel
참고4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
-
Install cabin intake upper duct assembly
참고4x clips, Heat pump vehicles have 3x clips
-
Install rear apron
참고12x clips
- Close hood
- Raise both front windows
- Close both front doors
-
Vehicle will need to be driven by customer to complete the calibration procedure. During this time DAS functions will be completely unavailable
참고No time was recorded as this will be completed by the customer