2023-01-25

Airbag - Knee - Driver (Remove and Install)

Correction code 20010201 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.
Informational PurposesAn informational icon, calling your attention
참고
운전석 무릎 에어백은 북미 차량에만 장착되어 있습니다.

Torque Specifications

표 1. Torque Specifications: Airbag - Knee - Driver (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
운전석 무릎 에어백을 차량에 고정하는 볼트(2개)
2 Nm (1.5 lbs-ft)
  • Torx T20 소켓
  • ¼인치 표준 래칫
  • 4인치 익스텐션
  • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
    • Wiha 토크 셋터
    • ¼인치~3/8인치 어댑터
운전석 무릎 에어백을 계기판에 고정하는 Torx T30 볼트(4개)
8 Nm (5.9 lbs-ft)
  • Torx T30 소켓
  • ¼인치 표준 래칫
운전석 무릎 에어백을 계기판에 고정하는 외부 Torx E10 볼트(4개)
8 Nm (5.9 lbs-ft)
  • 외부 Torx E10
  • 3/8인치 표준 래칫
  • 3인치 익스텐션
  • ¼인치 토크 렌치(장착 전용)
    • ¼인치~3/8인치 어댑터

Remove

  1. 모든 도어를 열고 모든 창문을 완전히 내립니다.
  2. LH 센터콘솔 사이드 패널 카펫을 탈거합니다. Side Panel - Center Console - LH (Remove and Replace)을(를) 참조하십시오.
  3. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  4. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  5. 운전석 발밑 공간 커버를 탈거합니다. Cover - Footwell - Driver (Remove and Replace)을(를) 참조하십시오.
  6. 운전석 무릎 에어백을 차량에 고정하는 T20 볼트(2개)를 탈거합니다.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • 4인치 익스텐션
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
      • Wiha 토크 셋터
      • ¼인치~3/8인치 어댑터
  7. 운전석 무릎 에어백을 계기판에 고정하는 볼트(4개)를 탈거하여 폐기합니다.
    8 Nm (5.9 lbs-ft)
    또는
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 소켓
    • ¼인치 표준 래칫
    또는
    • 외부 Torx E10
    • 3/8인치 표준 래칫
    • 3인치 익스텐션
    • ¼인치 토크 렌치(장착 전용)
      • ¼인치~3/8인치 어댑터
  8. 운전석 무릎 에어백 전기 하네스를 계기판 하단에 고정하는 클립을 분리합니다.
  9. 운전석 무릎 에어백에서 배선 하네스를 연결 해제한 다음 차량에서 에어백을 탈거합니다.

Install

Installation procedure is the reverse of removal, except for the following:

Informational PurposesAn informational icon, calling your attention
참고
운전석 무릎 에어백에 새 Torx 외부 E10 볼트(4개)를 장착합니다. Torx T30 볼트를 사용하지 마십시오(그림으로 표시됨).
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Replace all patchbolts.
  • 운전석 무릎 에어백 커버 후면 가장자리의 클립이 IP 캐리어에 체결되는지 확인합니다.