2020-12-16

Insert - Front Bin - Center Console (Remove and Replace)

Correction code 15195602 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Insert - Front Bin - Center Console (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Reuse
컵 홀더 하단 어셈블리를 센터 콘솔에 고정하는 나사
1.1 Nm (.8 lbs-ft)
  • Torx T20 소켓
  • 4인치 익스텐션
Reuse
센터 콘솔 전면 빈 인서트를 센터 콘솔에 고정하는 나사
1.1 Nm (.8 lbs-ft)
  • Torx T20 소켓
  • 4인치 익스텐션
Reuse

Remove

  1. LH 전면 플로어 매트를 탈거합니다.
  2. 센터콘솔을 탈거합니다. 참조 Center Console (Remove and Install)
  3. 접근할 수 있도록 센터콘솔 암레스트를 들어 올립니다.
  4. LH 및 RH 센터콘솔 장식 트림을 탈거합니다. Decor Trim - Center Console - LH (Remove and Replace)을(를) 참조하십시오.
  5. LH 브라이트 스트립을 센터콘솔에 고정하는 나사를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
  6. 브라이트 스트립을 센터콘솔에 고정하는 6개의 탭을 분리한 다음 브라이트 스트립을 탈거합니다.
  7. RH 브라이트 스트립을 센터콘솔에 고정하는 나사를 탈거합니다.
  8. 브라이트 스트립을 센터콘솔에 고정하는 6개의 탭을 분리한 다음 브라이트 스트립을 탈거합니다.
  9. 센터콘솔에 컵 홀더 장식을 고정하는 클립을 분리합니다.
  10. 보안 컨트롤러에서 전기 커넥터를 연결 해제한 다음, 컵 홀더 장식을 탈거합니다.
  11. 12V 콘센트와 퍼들 라이트에서 커넥터를 연결 해제합니다.
  12. 컵 홀더 어셈블리를 센터콘솔에 고정하는 나사를 분리합니다.
    1.1 Nm (.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
  13. 센터콘솔에 컵 홀더 어셈블리를 고정하는 클립을 분리한 다음 센터콘솔에서 컵 홀더 어셈블리를 탈거합니다.
  14. 센터콘솔 RH 쪽에서 커넥터를 연결 해제합니다.
  15. USB 컨트롤러에서 커넥터를 연결 해제합니다.
  16. 센터콘솔 전면 빈(bin) 인서트에 케이블을 고정하는 클립을 분리합니다.
  17. 센터콘솔 전면 빈 인서트를 센터콘솔에 고정하는 나사를 탈거합니다.
    1.1 Nm (.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
  18. 센터콘솔 전면 빈 인서트를 센터콘솔에 고정하는 클립(x4)을 분리한 다음 빈을 탈거합니다.

Install

Installation procedure is the reverse of removal.