Brake Lines - LH Sill (Remove and Replace)
Correction code
33035102
4.44
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
- 2025-05-09: 브레이크 라인 튜브 너트의 토크 규격을 16Nm로 업데이트했습니다.
- 1079041-00-A 플레어 너트 크로우풋 세트
Remove
-
경고
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
참고사용한 브레이크 오일은 현지 환경 규정에 따라 폐기합니다.
- LH 및 RH 하단 로커 패널 커버를 탈거합니다. Cover - Rocker Panel - Lower - LH (Remove and Replace)을(를) 참조하십시오.
- HV 배터리를 탈거합니다. HV Battery (RWD) (Remove and Install)을(를) 참조하십시오.
- LH 전면 휠 아치 라이너를 탈거합니다. Wheel Arch Liner - Front - LH (Remove and Replace)을(를) 참조하십시오.
- LH 후면 휠 아치 라이너를 탈거합니다. Wheel Arch Liner - Rear - LH (Remove and Replace)을(를) 참조하십시오.
- 전면 브레이크 라인 정션 블록 아래에 오일 배출 용기를 배치합니다.
-
정션 블록에서 브레이크 라인 튜브 너트를 탈거합니다. 오일을 배출합니다. 크로우풋 익스텐션을 사용하여 너트를 규격 토크로 조여 장착합니다.
16 Nm (11.8 lbs-ft)
- 후면 브레이크 라인 정션 블록 아래에 오일 배출 용기를 배치합니다.
-
정션 블록에서 브레이크 라인 튜브 너트를 탈거합니다. 오일을 배출합니다. 크로우풋 익스텐션을 사용하여 너트를 규격 토크로 조여 장착합니다.
16 Nm (11.8 lbs-ft)
-
후면 정션 블록을 차체에 고정하는 너트를 탈거하고 차체에서 블록을 분리합니다.7 Nm (5.2 lbs-ft)
-
브레이크 라인을 차체에 고정하는 클립을 풉니다.
-
차량에서 브레이크 라인을 탈거합니다.
Install
Installation procedure is the reverse of removal, except for the following:
-
경고
Replace all nyloc nuts.
경고Do not work on an incorrectly supported vehicle.
- 후면 캘리퍼용 브레이크 라인을 블리딩합니다. Brake Fluid Bleed - One Caliper을(를) 참조하십시오.