2025-09-11

Buckle - 1st Row - LH (Remove and Replace)

Correction code 20054702 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Buckle - 1st Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
버클을 시트 트랙에 고정하는 패치 볼트
40 Nm (29.5 lbs-ft)
  • Torx T50 소켓
  • 3/8인치 표준 래칫
  • 3/8인치 토크 렌치(장착 전용)
  • 3인치 익스텐션
Replace 1117250-00-A

Remove

  1. 내측 사이드 실드를 탈거합니다. 참조 항목: Side Shield - Inboard - Driver Seat (Remove and Replace).
  2. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  3. LH 1열 버클에서 전기 커넥터를 연결 해제합니다.
  4. 시트 하부 프레임에서 하네스 클립을 분리합니다.
  5. 버클을 시트 트랙에 고정하는 패치 볼트를 탈거하여 폐기한 다음 버클을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
    • 3인치 익스텐션

Install

  1. 버클을 시트 트랙에 고정하기 위해 새 안전벨트 버클과 함께 제공되는 패치 볼트를 장착합니다.
    40 Nm (29.5 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    버클의 핀이 시트 트랙의 슬롯에 잘 맞아야 합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 3/8인치 표준 래칫
    • 3/8인치 토크 렌치(장착 전용)
    • 3인치 익스텐션
  2. LH 1열 버클에 전기 커넥터를 연결합니다.
  3. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  4. 시트를 가장 높은 위치로 올리고 안전벨트 버클 하네스를 손전등으로 검사하여 아무것도 걸리지 않는지 확인합니다.
  5. 안전벨트 버클 하네스가 기준점을 돌아가지 않고 기준점 앞에 배치하십시오.
  6. 시트를 여전히 가장 높은 위치로 올린 상태에서 안전벨트 버클 하네스 클립을 내측 시트 레일을 따라 조정 및 고정하고, 클립 뒤쪽의 처짐을 제거하기 위해서 하네스가 최대한 앞쪽으로 확장되어 있는지 확인합니다.
  7. 시트를 완전히 올렸다 내리고 안전벨트 버클 하네스를 손전등으로 검사하여 아무것도 걸리지 않은지 확인합니다.
  8. 내측 사이드 실드를 장착합니다. 참조 항목: Side Shield - Inboard - Driver Seat (Remove and Replace).