2023-04-20

Shroud - Lower - Steering Column (Remove and Replace)

Correction code 32051202 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. LH 전면 도어를 열고 모든 창문을 완전히 내립니다.
  2. 차량의 전륜 휠을 일직선으로 정렬하고 스티어링 휠을 중앙으로 정렬합니다.
  3. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  4. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  5. 운전석 에어백을 탈거합니다. Airbag - Driver (Remove and Replace)을(를) 참조하십시오.
  6. 스티어링 휠을 탈거합니다. Steering Wheel (Remove and Install)을(를) 참조하십시오.
  7. 스티어링 컬럼 상단 슈라우드를 하단 슈라우드에 고정하는 클립을 분리한 다음 상단 슈라우드를 위로 당깁니다.
  8. 스티어링 컬럼 하단 슈라우드를 스티어링 컬럼에 고정하는 상단 나사를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • 2인치 익스텐션
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
      • Torx T20 비트, 70mm
      • Wiha ¼인치 비트 홀더 어댑터
      • Wiha 토크 셋터
  9. 스티어링 컬럼 하단 슈라우드를 스티어링 컬럼에 고정하는 하단 나사를 탈거한 다음 차량에서 하단 슈라우드를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • 2인치 익스텐션
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
      • Torx T20 비트, 70mm
      • Wiha ¼인치 비트 홀더 어댑터
      • Wiha 토크 셋터

Install

  1. 스티어링 컬럼 하단 슈라우드를 스티어링 컬럼에 배치한 다음 슈라우드를 스티어링 컬럼에 고정하는 하단 나사를 장착합니다.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • 2인치 익스텐션
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
      • Torx T20 비트, 70mm
      • Wiha ¼인치 비트 홀더 어댑터
      • Wiha 토크 셋터
  2. 스티어링 컬럼 하단 슈라우드를 스티어링 컬럼에 고정하는 상단 나사를 장착합니다.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • 2인치 익스텐션
    • Wiha TorqueVario-S 0.8Nm - 2.0Nm 스크루드라이버(장착 전용)
      • Torx T20 비트, 70mm
      • Wiha ¼인치 비트 홀더 어댑터
      • Wiha 토크 셋터
  3. 상단 슈라우드를 하단 슈라우드에 고정하는 클립을 장착합니다.
  4. 스티어링 휠을 장착합니다. Steering Wheel (Remove and Install)을(를) 참조하십시오.
  5. 운전석 에어백을 장착합니다. Airbag - Driver (Remove and Replace)을(를) 참조하십시오.
  6. 12V 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  7. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.