AC 케이블 - 충전 포트-HV 배터리(3상)(새로 장착)
Correction code 44501406 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
- 1076921-00-B 절연 멀티미터, Fluke 1507(북미)
- 1108272-00-B 캡, 로직 연결, 인버터, 3DU
- 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
- 1115203-00-A 미터법/6인치 포켓 자
Only
technicians who have completed all required certification courses are permitted to
perform this procedure. Tesla recommends third party service provider technicians
undergo equivalent training before performing this procedure. For more information on
Tesla Technician requirements, or descriptions of the subject matter for third parties,
see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV
gloves with a minimum rating of class 0 (1000V) must
be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness
Care Points
for additional safety
information.
Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.
이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.
- 고전압(HV) 절연 장갑
- 가죽 장갑 보호구
- 고전압 장갑 테스터
- 보안경
- 전기 위험 등급 안전 장화
장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.
HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.
Retrofit
- AC 케이블 - 충전 포트-HV 배터리를 탈거합니다. 참조 항목: AC Cable - Charge Port to HV Battery (3-Phase) (Remove and Replace).
-
10mm 실리콘 고무 4개를 절단합니다.
-
뒷면 접착제를 떼어낸 다음 커넥터의 지정된 영역에 가지런히 붙여 실리콘 고무를 AC 3상 커넥터에 장착합니다.
- AC 케이블 - 충전 포트-HV 배터리를 장착합니다. 참조 항목: AC Cable - Charge Port to HV Battery (3-Phase) (Remove and Replace).