2024-09-09

Tire - Front - LH (Repair)

Correction code 34023008 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Always read and understand the tire equipment operator’s manual and on-screen instructions before operating the wheel balancer or tire changer.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Always make sure to properly secure the wheel and exercise caution around all moving parts and pinch points, including the indent rollers. Additionally, secure all loose items such as hair, jewelry, and clothing, so that they will not catch on moving parts.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The machine must be operated by no more than one person at a time. Other persons must maintain a safe distance of at least three feet from equipment while in use.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Never use equipment that is defective or not working as expected based on the equipment operator’s manual.
Informational PurposesAn informational icon, calling your attention
참고
These instructions are based on the Hunter GSP9700 wheel balancer. Some steps might be different for other wheel balancers. Refer to the operator's manual and on-screen instructions for specific information.
그림 1. MY에서 본 모습, 다른 모델도 유사함
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

검사

  1. 휠을 탈거합니다. Wheel Assembly (Remove and Install)을(를) 참조하십시오.
  2. 타이어 바깥쪽을 검사합니다. 다음과 같은 상태인 경우 절차를 중단하고 타이어를 교체합니다. Tire - Front - LH (Tire Purchase)을(를) 참조하십시오. 타이어를 수리하지 마십시오.
    • 숄더 또는 사이드월에 펑크가 있음.
    • 물체가 타이어에 15도 이상 수직으로 파고듦.
    • 물체가 직경 1/4인치 이상임.
    • 트레드 깊이가 1/16인치 미만임.
    • 사이드월에 깊이가 1/16인치를 초과하는 균열이 있음.
    • 타이어가 10년이 넘음.
  3. 휠에서 타이어를 탈거합니다. Tire - Front - LH (Tire Purchase)을(를) 참조하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    이후 밸런스를 간소화하기 위해 타이어 및 휠 장착 위치를 표시합니다.
  4. 타이어 안쪽을 검사합니다. 다음과 같은 상태인 경우 절차를 중단하고 새 타이어를 휠에 장착합니다. Tire - Front - LH (Tire Purchase)을(를) 참조하십시오. 타이어를 수리하지 마십시오.
    • 타이어에 펑크가 난 상태로 주행한 흔적이 있음. 내측 사이드월의 균열, 분리 또는 푸르스름한 색상으로 이를 식별할 수 있습니다.
    • 이전에 수리한 부분이 펑크에 매우 근접하여 수리 영역이 중복됨.
    • 이전 수리가 적절하지 않았음.
    • 비드의 파손, 주름 또는 손상.
    • 눈에 띄는 모든 내부 손상.
  5. 타이어를 수리합니다. 수리을(를) 참조하십시오.

수리

  1. 펑크가 있는 위치의 타이어 바깥쪽 및 안쪽에 모두 표시합니다.
  2. 물체를 제거합니다.
  3. 타이어에 폼 흡음재가 있는 경우 펑크에서 지름 50mm로 폼을 절단합니다.
  4. 카바이드 절단기를 사용하여 펑크를 정리합니다.
  5. 타이어 안쪽에서 미니콤비 인서트를 펑크에 가운데 정렬하고 인서트보다 약 15mm더 크게 원을 그립니다.
  6. 원을 그린 영역에 버핑 전 세척제를 도포합니다.
  7. 라이너 스크래퍼를 사용하여 원을 그린 영역을 긁어냅니다.
  8. 원을 그린 영역이 완전히 정리될 때까지 6단계~ 7단계를 반복합니다.
  9. 원을 그린 영역이 부드러워질 때까지 가볍게 버핑합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    코드가 노출된 경우 절차를 중단하고 새 타이어를 휠에 장착합니다. Tire - Front - LH (Tire Purchase)을(를) 참조하십시오.
  10. 타이어 안쪽의 잔해를 진공 인입합니다.
  11. 블루 시멘트를 펑크에 바른 다음 원을 그린 영역에 얇게 도포합니다.
  12. 미니콤비 인서트에서 보호 커버를 제거한 다음 가이드 핀을 펑크에 삽입하여 타이어 트레드로 빼냅니다.
  13. 플라이어를 사용하여 미니콤비 인서트 베이스가 타이어 안쪽 면과 같은 높이가 되고, 약간 움푹 파인 곳이 생길 때까지 가이드 핀을 당깁니다.
  14. 가운데에서 바깥쪽을 향해 스티처를 굴려서 베이스를 타이어에 완전히 접착합니다.
  15. 베이스에서 보호 커버를 제거하고 베이스 및 원을 그린 영역에 씰런트를 넉넉하게 도포합니다.
  16. 트레드와 같은 높이가 되도록 가이드 핀을 절단합니다.
  17. 타이어를 휠에 장착합니다. Tire - Front - LH (Tire Purchase)을(를) 참조하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    타이어를 탈거하기 전에 표시한 위치 표시를 사용합니다.