2025-03-07

Oil Pump - Front Drive Unit (Remove and Replace)

Correction code 39301602 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-04-05: 기어박스 오일 정보와 링크를 업데이트했습니다.
  • 2024-02-27: 기어박스 오일을 KAF 1로 업데이트했습니다.
  • 1081765-00-A 3/4톤 언더호이스트 스탠드

Remove

  1. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  2. 전륜 구동 장치 기어박스 오일을 배출합니다. 참조 항목: Gearbox Fluid - Front Drive Unit (Drain and Refill).
    Informational PurposesAn informational icon, calling your attention
    참고
    Tesla recommends that the oil filter is replaced with a new one upon removal. Any oil filter with visible corrosion or leaks must be replaced.
  3. 전륜 구동 장치의 LH 측을 그림과 같이 언더호이스트 스탠드로 지지합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    정비소 타월을 언더호이스트 스탠드와 전륜 구동 장치 사이에 놓습니다.
  4. 전륜 구동 장치를 전면 서브프레임에 고정하는 볼트를 탈거합니다.
    80 Nm (59.0 lbs-ft)
  5. 전륜 구동 장치 오일 펌프에 접근할 수 있을 때까지 전면 언더호이스트 스탠드를 주의하여 내립니다.
  6. 전륜 구동 장치 오일 펌프를 전륜 구동 장치에 고정하는 볼트를 탈거합니다.
    5 Nm (3.7 lbs-ft) + 20 degrees
  7. 전륜 구동 장치 오일 펌프를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    전륜 구동 장치를 지렛대로 사용하여 오일 펌프를 들어 올려 분리합니다.

Install

  1. 오일 펌프 O링을 깨끗한 기어박스 오일로 가볍게 코팅합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    해당하는 기어박스 오일을 확인하려면 유액 및 용량의 내용을 참조하십시오.
  2. 전륜 구동 장치에 오일 펌프를 장착합니다.
  3. 오일 펌프를 전륜 구동 장치에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft) + 20 degrees
  4. 전륜 구동 장치 부싱이 전면 서브프레임 마운트와 정렬될 때까지 전면 언더호이스트 스탠드를 주의하여 올립니다.
  5. 전륜 구동 장치를 전면 서브프레임에 고정하는 볼트를 장착합니다.
    80 Nm (59.0 lbs-ft)
  6. 전륜 구동 장치의 LH에서 언더호이스트 스탠드와 작업용 타월을 제거합니다.
  7. 전륜 구동 장치 기어박스 오일을 보충합니다. 참조 항목: Gearbox Fluid - Front Drive Unit (Drain and Refill).
  8. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Remove and Replace).
  9. 12V 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  10. 차량 소프트웨어를 업데이트합니다. 참조 항목: Software Update.