2026-11-03

스포크 커버 - 스티어링 휠 - 하단(탈거 및 교체)

교정 코드 32051822 0.24 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-11-03: Updated the specification of the bolts (x4) that attach the bright surround to the steering wheel.

탈거

  1. Disconnect LV power. See 12V/LV 전원(연결 해제 및 연결).
  2. Remove the driver airbag. See 에어백 - 운전석(탈거 및 교체).
  3. Disconnect the steering wheel electrical wiring harness from the connector.
  4. Disconnect the electrical harness from the LH steering wheel switch connector.
  5. Disconnect the electrical harness from the RH steering wheel switch connector.
  6. Release the clips that attach the horn assembly, and then move the horn assembly to the side.
  7. Disconnect the electrical harness from the lower connector, and then remove the electrical harness from the steering wheel.
  8. Remove the bolts that attach the steering wheel surround to the steering wheel.
    Note
    Pry the lower portion of the bright surround assembly away from the steering wheel, and then work your way around.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  9. Remove the bolts (x2) that attach the steering wheel controller to the steering wheel surround, and then remove the controller.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 비트
  10. Remove the bolts that attach the lower spoke cover to the steering wheel surround.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 비트

장착

  1. Position the lower spoke cover onto the steering wheel surround, and then install the bolts.
    0.9 Nm (8 lbs-in)
    Note
    Insert the lower edge of the lower spoke.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 비트
  2. Install the bolts that attach the steering wheel controller to the steering wheel surround.
    0.9 Nm (8 lbs-in)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 비트
  3. Position the steering wheel surround onto the steering wheel, and then install the bolts.
    2.5 Nm (1.8 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  4. Install the electrical harness into the steering wheel, and then connect the electrical harness to the lower connector.
  5. Move the horn assembly to the center, and then fasten the clips that attach the horn assembly.
  6. Connect the electrical harness to the RH steering wheel switch connector.
  7. Connect the electrical harness to the LH steering wheel switch connector.
  8. Connect the steering wheel electrical harness to the connector.
  9. Install the driver airbag. See 에어백 - 운전석(탈거 및 교체).
  10. Connect LV power. See 12V/LV 전원(연결 해제 및 연결).