2021-01-29

HV Harness - Center Ski to A/C Compressor (Remove and Replace)

Correction code 44501302 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Remove

  1. 차량을 들어 올려서 지지합니다. Raise Vehicle - 2 Post Lift을(를) 참조하십시오.
  2. 외기 흡기 덕트를 탈거합니다. Duct - Fresh Intake (Remove and Replace)을(를) 참조하십시오.
  3. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  4. 차량 전기 절연 절차를 수행합니다. Vehicle HV Disablement Procedure을(를) 참조하십시오.
  5. 전면 에어로 실드 패널을 탈거합니다. Panel - Aero Shield - Front (Remove and Replace)을(를) 참조하십시오.
  6. HV 배터리 전면 근처에 있는 센터 스키-AC 컴프레서 하네스 커넥터(2개)를 찾습니다.
  7. 커넥터 2개 각각에서 빨간색 잠금 탭을 커넥터 몸체에서 당긴 다음 초록색 잠금 탭을 눌러 커넥터를 연결 해제합니다.
  8. 방화벽 LH 쪽 근처에 있는 스터드에서 HV 커넥터 브래킷을 분리합니다.
  9. 센터 스키-AC 컴프레서 하네스를 방화벽 RH 쪽에 있는 스터드에 고정하는 클립(2개)을 분리합니다.
  10. 차량을 작업하기 편안한 높이로 내립니다.
  11. 센터 스키-AC 컴프레서 하네스를 전면 하네스 가이드 커버에 고정하는 클립을 분리합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이 클립을 분리하는 동안 HV 하네스를 당기지 마십시오.
    Informational PurposesAn informational icon, calling your attention
    TIp
    해당 클립은 RH 스트럿 타워 주변에 있습니다.
  12. A/C 컴프레서 HV 하네스를 스트럿 타워 서포트 브레이스에 고정하는 클립을 분리합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    HV 하네스를 당기지 마십시오.
  13. 커넥터 잠금 탭을 분리한 다음 LH 전면 스트럿 타워 근처에 있는 HVIL 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  14. 커넥터 잠금 탭을 분리한 다음 A/C 컴프레서에서 저전압 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  15. A/C 컴프레서 저전압 하네스를 A/C 컴프레서 HV 하네스 브래킷에 고정하는 클립을 분리합니다.
  16. HV 하네스 브래킷을 A/C 컴프레서에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  17. A/C 컴프레서에서 A/C 컴프레서 HV 커넥터 검은색 잠금 탭을 당겨 분리합니다.
  18. 45도 픽(쪼는) 도구를 사용하여 외측 잠금 탭을 당기는 동시에 중앙 잠금 탭을 누르고 A/C 컴프레서에서 HV 커넥터를 탈거합니다.
  19. 센터 스키-A/C 컴프레서 하네스 브래킷을 앞으로 이동하여 위로 들어 A/C 컴프레서에서 하네스 브래킷을 분리한 다음 차량에서 하네스를 주의하여 탈거합니다.

Install

  1. A/C 컴프레서 HV 하네스 브래킷을 A/C 컴프레서에 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    HV 하네스 브래킷이 표시된 대로 A/C 컴프레서 상단부의 하네스 마운트에 체결되는지 확인합니다.
  2. A/C 컴프레서 HV 커넥터를 A/C 컴프레서에 완전히 안착시킨 다음 잠금 탭을 A/C 컴프레서를 향해 밀어 체결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the connector is fully attached.
  3. HV 하네스 브래킷을 A/C 컴프레서에 고정하는 볼트를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  4. A/C 컴프레서 저전압 하네스를 A/C 컴프레서 HV 하네스 브래킷에 고정하는 클립을 장착합니다.
  5. 저전압 전기 커넥터를 A/C 컴프레서에 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  6. LH 전면 스트럿 타워 근처에 있는 HVIL 커넥터를 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  7. A/C 컴프레서 HV 하네스를 스트럿 타워 서포트 브레이스에 고정하는 클립을 장착합니다.
  8. 센터 스키-A/C 컴프레서 하네스를 벌크헤드에 대고 아래로 배치한 다음 하네스를 전면 하네스 가이드 커버에 고정하는 클립을 장착합니다.
  9. 차량을 들어 올립니다.
  10. 센터 스키-AC 컴프레서 하네스를 방화벽 RH 쪽에 있는 스터드에 고정하는 클립(2개)을 장착합니다.
  11. 방화벽 LH 쪽 근처에 있는 스터드에 HV 커넥터 브래킷을 장착합니다.
  12. 센터 스키-A/C 컴프레서 하네스 커넥터(2개)를 센터 스키 하네스에 연결합니다. 초록색 잠금 장치가 딸깍 소리를 내면서 체결되는지 확인합니다.
  13. 빨간색 잠금 탭을 커넥터 몸체를 향해 밀어 커넥터(2개)를 완전히 잠급니다.
  14. 전면 에어로 실드 패널을 장착합니다. Panel - Aero Shield - Front (Remove and Replace)을(를) 참조하십시오.
  15. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  16. 12V 전원을 다시 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  17. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.