2025-06-27

Tire - Front - LH (Tire Purchase)

Correction code 34021002 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-05-23: 윤활제 건조 시간에 대한 주의사항을 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Always read and understand the tire equipment operator’s manual and on-screen instructions before operating the wheel balancer or tire changer.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Always make sure to properly secure the wheel and exercise caution around all moving parts and pinch points, including the indent rollers. Additionally, secure all loose items such as hair, jewelry, and clothing, so that they will not catch on moving parts.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The machine must be operated by no more than one person at a time. Other persons must maintain a safe distance of at least three feet from equipment while in use.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Never use equipment that is defective or not working as expected based on the equipment operator’s manual.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
타이어 윤활제가 완전히 마를 때까지 최대 24시간이 소요될 수 있습니다. 이 기간 동안 림의 타이어 슬립을 피하도록 급가속을 하지 마십시오.
Informational PurposesAn informational icon, calling your attention
참고
이 지침은 Hunter TC3900 타이어 교환에 기초하였습니다. 다른 타이어 교환기에는 일부 단계가 다를 수 있습니다. 운영자 설명서의 특수 정보를 참조해 주십시오.

마운트 해제

  1. 휠을 탈거합니다. Wheel Assembly (Remove and Install) 을(를) 참조하세요.
  2. 휠의 정면이 위를 향하도록 하여 타이어 교환기에 휠을 놓습니다.
  3. 중앙 클램프를 삽입합니다.
  4. 중앙 클램프에 콘을 단단하게 조입니다.
  5. 밸브 코어를 탈거하여 타이어 공기를 배출합니다.
  6. 림 가장자리에 상단 비드 롤러를 배치합니다.
  7. 타이어를 회전시켜서 상단 비드를 이완시킵니다. 타이어가 회전할 때 비드를 윤활합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    TPMS 센서가 림에 가까이에 있습니다. 상단 비드를 풀 때에 TPMS 센서가 손상되지 않도록 하십시오.
  8. 하단 비드 롤러를 림 가장자리에 위치시킵니다.
  9. 타이어를 회전시켜서 하단 비드를 이완시킵니다. 타이어가 회전할 때 비드를 윤활합니다.
  10. 마운트 헤드를 림 가장자리에 위치시킨 후, 마운트 헤드를 들어 올려서 상단 비드를 후크로 고정합니다.
  11. 타이어를 회전시켜서, 림 위로 상단 비드를 당깁니다. 타이어가 회전할 때 비드를 윤활합니다.
  12. 하단 비드 롤러를 사용하여 림 밖으로 타이어를 들어 올립니다.

마운트

  1. 새 타이어 양쪽 비드를 완전히 윤활합니다.
  2. 타이어에 "외측", "바깥쪽으로 향하는 측면" 또는 사이드월의 회전 화살표 방향이 있는 경우에는, 타이어가 올바른 방향으로 되어 있는지 확인합니다.
  3. 손으로 타이어의 하단 비드를 림 위로 밀어 넘깁니다.
  4. 마운트 헤드를 상단 비드에 배치합니다.
  5. 비드 프레스 암을 사용하여 사이드월을 밑으로 누릅니다.
  6. 타이어를 천천히 회전시켜서, 림 밑의 상단 비드를 누릅니다.
  7. 에어척을 밸브 스템에 고정합니다.
  8. 풋 페달을 사용하여 약 40PSI(275kPa)로 타이어를 팽창시켜 비드를 안착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    페달에서 발을 떼면 압력 게이지가 정확한 압력을 나타냅니다. 페달을 반복적으로 누르고 해제하여 과대 팽창을 방지합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    타이어 사이드월에 표시한 압력을 초과하지 마십시오.
  9. 밸브 스템에서 에어척을 탈거한 다음 밸브 코어를 장착합니다.
  10. 휠 크기에 따라 타이어 공기압을 설정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    도어 잼에 표시된 타이어 스티커 값을 사용하십시오. 사용할 수 없는 경우 다음 값을 사용하십시오.
    • 18인치 휠 - 42psi
    • 19인치 휠 - 42psi
  11. 타이어 밸런스를 맞춥니다. Tire - Front - LH (Balance)을(를) 참조하십시오.
  12. 휠을 설치합니다. Wheel Assembly (Remove and Install) 을(를) 참조하세요.
  13. 2개 이상의 타이어를 교체하는 경우 다음 단계를 수행합니다.
    1. 터치스크린을 사용하여 차량을 정비 모드로 설정합니다. Service Mode 을(를) 참조하세요.
    2. 차량 게이트웨이를 잠금 해제합니다. 게이트웨이(잠금 해제) 을(를) 참조하세요.
    3. 터치스크린에서 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Chassis > Alignment & Tires > Reset Learned Tire Values를 탭하고 Run을 클릭하여 루틴이 완료될 때까지 기다립니다.
    4. Controls > Service > Wheel & Tire > Tires를 탭하고, tire season을 선택하고 Reset을 클릭합니다. 초기화 후 오른쪽 상단에 Tire Service MileageLess than 500 km ago로 표시되는지 확인합니다.
    5. 정비 모드를 종료합니다. Service Mode 을(를) 참조하세요.
    6. LH 전면 도어를 닫습니다.
    7. 고객에게 짧은 보정 주행 사이클이 필요할 수 있음을 알립니다.