2024-09-09

Oil Pump - Rear Drive Unit (3DU) (Remove and Replace)

Correction code 40304602 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-08-15: 오일 펌프 관련 Toolbox 루틴전에 소프트웨어 재설치를 수행하도록 지침을 추가했습니다.
  • 2024-04-05: 기어박스 오일 정보와 링크를 업데이트했습니다.
  • 2024-02-27: 기어박스 오일을 KAF 1로 업데이트했습니다.
  • 2023-11-10: 공구 정보를 추가했습니다.

Remove

  1. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  2. 후륜 구동 장치에서 기어박스 오일을 배출합니다. 참조 항목: Gearbox Fluid - Rear Drive Unit (3DU) (Drain and Refill).
  3. 오일 펌프를 후륜 구동 장치에 고정하는 볼트를 탈거한 후 후륜 구동 장치에서 펌프를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • EPL10 소켓
    • 4인치 익스텐션
  4. 프라이툴로 오일 펌프를 들어 올려 후륜 구동 장치에서 헐거워지게 합니다.
  5. 후륜 구동 장치 어셈블리에서 오일 펌프를 탈거합니다.

Install

  1. 오일 펌프 O링을 깨끗한 기어박스 오일로 가볍게 코팅합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    해당하는 기어박스 오일을 확인하려면 유액 및 용량의 내용을 참조하십시오.
  2. 오일 펌프를 후륜 구동 장치에 장착한 후 오일 펌프를 후륜 구동 장치에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft) + 20 degrees
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • EPL10 소켓
    • 4인치 익스텐션
  3. 후륜 구동 장치용 기어박스 오일을 보충합니다. 참조 항목: Gearbox Fluid - Rear Drive Unit (3DU) (Drain and Refill).
    Informational PurposesAn informational icon, calling your attention
    참고
    오일 펌프 관련 Toolbox 루틴을 실행하기 직전에 차량 소프트웨어를 재설치합니다. 참조 항목: Software Reinstall - Touchscreen.
  4. 접근하기 위해 탈거한 모든 구성품을 설치합니다.