2025-03-03

Speaker - Pedestrian Warning (Remove and Replace)

Correction code 17541002 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-09-12: 효율성을 개선하기 위해 절차를 최적화했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Remove

  1. RH 전면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  2. RH 전면 휠 라이너를 페시아에 고정하는 클립(9개)을 탈거하고 접근을 위해 휠 라이너를 한쪽으로 치워둡니다.
  3. 하네스를 보행자 경고 스피커 어셈블리에 고정하는 클립을 탈거합니다.
  4. 잠금 탭을 커넥터에서 밀어 분리한 다음, 회색 잠금 탭을 눌러 보행자 경고 스피커 커넥터를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터 접근 방식은 차량에 장착된 슈퍼혼 오디오 스피커 버전에 따라 다를 수 있습니다. 훼손 방지 기능으로 덮여 있는 빨간색 잠금 탭을 풀려면 포켓 드라이버나 소형 픽을 사용해야 할 수도 있습니다.
  5. 보행자 경고 스피커 어셈블리를 전면 페시아에 고정하는 나사(3개)를 탈거한 다음, 페시아에서 보행자 경고 스피커를 탈거합니다.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 2인치 익스텐션
    • Torx T25 소켓
    • 래칫/토크 렌치

Install

  1. 보행자 경고 스피커 어셈블리를 전면 페시아에 고정하는 나사(3개)를 장착합니다.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 2인치 익스텐션
    • Torx T25 소켓
    • 래칫/토크 렌치
  2. 잠금 탭을 체결하여 보행자 경고 스피커 커넥터를 연결합니다.
  3. 하네스를 보행자 경고 스피커 어셈블리에 고정하는 클립을 장착합니다.
  4. RH 전면 휠 라이너를 페시아에 고정하는 클립(9개)을 장착합니다.
  5. RH 전면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).