2026-11-03

스위치 - 스티어링 휠- RH(탈거 및 교체)

교정 코드 17300802 0.24 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-11-03: Updated the specification of screws (x4) that attach the bright surround to the steering wheel.

탈거

  1. Remove the driver airbag. See 에어백 - 운전석(탈거 및 교체).
  2. Disconnect the steering wheel electrical wiring harness from the connector.
  3. Disconnect the electrical harness from the LH steering wheel switch connector.
  4. Disconnect the electrical harness from the RH steering wheel switch connector.
  5. Release the clips that attach the horn assembly, and then move the horn assembly to the side.
  6. Disconnect the electrical harness from the lower connector, and then remove the electrical harness from the steering wheel.
  7. Remove the screws (x4) that attach the bright surround to the steering wheel, and then remove the surround.
    2.5 Nm (1.8 lbs-ft)
    Note
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  8. Remove the screws (x3) that attach the RH steering wheel switch to the bright surround, and then remove the switch from the surround.
    0.9 Nm (8 lbs-in)

장착

  1. Install the RH steering wheel switch into the bright surround, and then install the screws (x3) that attach the switch to the surround.
    0.9 Nm (8 lbs-in)
  2. Install the bright surround into the steering wheel, and then install the screws (x4) that attach the surround to the steering wheel.
    2.5 Nm (1.8 lbs-ft)
    Note
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  3. Install the electrical harness into the steering wheel, and then connect the electrical harness to the lower connector.
  4. Move the horn assembly to the center, and then fasten the clips that attach the horn assembly.
  5. Connect the electrical harness to the RH steering wheel switch connector.
  6. Connect the electrical harness to the LH steering wheel switch connector.
  7. Connect the steering wheel electrical harness to the connector.
  8. Install the driver airbag. See 에어백 - 운전석(탈거 및 교체).
  9. 차량 펌웨어를 다시 설치합니다. 참조 항목: 소프트웨어 재설치 - 터치스크린.
  10. Connect a laptop with Toolbox 3 to the vehicle.
  11. In Toolbox, click the Actions tab, type "VCLEFT" in the search field, click onTEST-SELF_VCLEFT_X_SWCvia Toolbox:(link), and then select Run.
  12. Click the Actions tab, type "VCLEFT" in the search field, click on TEST-RESET_VCLEFTvia Service Mode Plus:Chassis ➜ SCCM ➜ Reset VCLeftvia Toolbox:(link), and then select Run.
  13. Disconnect the laptop from the vehicle.