2024-09-16

Shear Plate - Rear Subframe - Front - LH (Remove and Replace)

Correction code 30011502 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Shear Plate - Rear Subframe - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 시어 플레이트를 HV 배터리에 고정하는 소형 볼트
35 Nm (25.8 lbs-ft)
  • 13mm 소켓
  • 3인치 익스텐션
Reuse
LH 시어 플레이트 및 후면 서브프레임을 차체에 고정하는 대형 볼트
130 Nm (95.9 lbs-ft)
  • 21mm 소켓
  • 6인치 익스텐션
Replace

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  3. 중앙 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Rear (Remove and Replace).
  4. 언더호이스트 스탠드를 사용하여 후면 서브프레임의 전면부를 지지합니다.
  5. 냉각수 호스를 LH 시어 플레이트에 고정하는 퍼트링 클립을 풉니다.
  6. LH 시어 플레이트를 HV 배터리에 고정하는 소형 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 3인치 익스텐션
  7. LH 시어 플레이트와 후면 서브프레임을 차체에 고정하는 대형 볼트를 탈거하여 폐기한 다음 LH 시어 플레이트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21mm 소켓
    • 6인치 익스텐션

Install

  1. LH 시어 플레이트를 후면 서브프레임 및 HV 배터리에 장착한 다음 새 볼트를 손으로 조여 시어 플레이트를 서브프레임에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    이 절차의 이후 단계에서 볼트 조이기를 수행합니다.
  2. LH 시어 플레이트를 HV 배터리에 고정하는 소형 볼트를 장착합니다.
    35 Nm (25.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 3인치 익스텐션
  3. LH 시어 플레이트를 차량에 고정하는 큰 볼트를 규격 토크로 조인 다음 페인트 펜으로 볼트에 표시합니다.
    130 Nm (95.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21mm 소켓
    • 6인치 익스텐션
  4. LH 시어 플레이트에 냉각수 호스를 고정하는 퍼트리 클립을 고정합니다.
  5. 차량 아래에서 언더호이스트 스탠드를 제거합니다.
  6. 중앙 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Rear (Remove and Replace).
  7. LH 전면 도어를 닫고 LH 전면 창문을 올립니다.
  8. 리프트에서 차량을 내립니다. 참조 항목: Raise Vehicle - 2 Post Lift.