2025-09-23

Handle - Exterior Release - Door - Front - LH (Remove and Replace)

Correction code 11451002 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-09-01: LV 배터리 전원 연결 해제/연결 단계를 추가하고, 창문 보정 루틴을 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The side impact airbag deployment depends on the front door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the front door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the front doors and their components.

Remove

  1. LH 전면 도어 트림 패널을 탈거합니다. 참조 항목: Panel - Door Trim - Front - LH (Remove and Install).
  2. LH 전면 도어 내측 벨트 씰을 탈거합니다. 참조 항목: Seal - Inner Belt - Front Door - LH (Remove and Replace).
  3. 전면 LH 도어 글라스를 탈거합니다. 참조 항목: Glass - Door - LH - Front (Remove and Replace).
  4. LV 배터리 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. LH 전면 도어 클로즈아웃 패널을 탈거합니다. 참조 항목: 클로즈아웃 패널 - 도어 - 전면 - LH(탈거 및 교체).
  6. 도어 핸들 커넥터에서 전기 배선 하네스를 연결 해제합니다.
  7. 도어 핸들 너트에 접근 경로를 덮는 플러그를 탈거합니다.
  8. 도어 핸들을 도어에 고정하는 너트를 탈거한 다음 도어에서 핸들을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓

Install

  1. 도어 핸들을 도어에 고정하는 너트(3개)를 손으로 조입니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Nyloc 너트를 교체하지 않습니다. 마운팅 스터드 한 개당 심을 2개 이상 겹쳐서 장착하지 마십시오. 확인 결과에 따라 필요한 경우 핸들 마운팅 스터드에서 핸들과 도어 내부 표면 사이에 심을 끼워 핸들과의 간격 및 단차를 조절합니다.
  2. LH 전면 도어 핸들 간격 및 단차가 규격 이내인지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    현재 규격은 CVIS를 참조하십시오.
  3. 도어 핸들을 도어에 고정하는 너트(3개)를 규격 토크로 조입니다.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  4. 도어 핸들 너트 접근을 가리는 플러그를 장착합니다.
  5. 도어 핸들 커넥터에 전기 배선 하네스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터를 완전히 안착한 다음 잠금 탭을 체결합니다.
  6. LH 전면 도어 클로즈아웃 패널을 장착합니다. 참조 항목: 클로즈아웃 패널 - 도어 - 전면 - LH(탈거 및 교체).
  7. LV 배터리 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  8. 전면 LH 도어 글라스를 장착합니다. 참조 항목: Glass - Door - LH - Front (Remove and Replace).
  9. LH 전면 도어 내측 벨트 씰을 장착합니다. 참조 항목: Seal - Inner Belt - Front Door - LH (Remove and Replace).
  10. LH 전면 도어 트림 패널을 장착합니다. 참조 항목: Panel - Door Trim - Front - LH (Remove and Install).
  11. 터치스크린을 사용하여 차량을 정비 모드로 설정합니다. 참조 항목: Service Mode.
  12. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  13. LH 전면 도어를 닫습니다.
  14. 터치스크린에서, 정비 모드 "렌치"(터치스크린 UI 하단)를 탭한 다음 Closures > Windows > Calibrate Windows > Run을 탭하고 루틴이 완료될 때까지 기다립니다.
  15. 정비 모드를 종료합니다. 참조 항목: Service Mode.