2025-06-27

Buckle - 2nd Row - Center (Remove and Replace)

Correction code 20057202 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-06-29: 탈거 부분의 4단계에 비디오를 추가했습니다.
  • 2152873-00-A 도구, 유도성 가열

Torque Specifications

표 1. Torque Specifications: Buckle - 2nd Row - Center (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
RH 및 중앙 버클을 차체에 고정하는 볼트
40 Nm (29.5 lbs-ft)
  • 15mm 소켓
  • 3인치 익스텐션
Replace

Remove

  1. 2열 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  2. RH 및 중앙 시트 버클 전기 커넥터를 연결 해제합니다.
  3. 전기 커넥터의 암 쪽을 차체 스터드에 고정하는 브래킷을 분리합니다.
  4. 볼트를 탈거하여 폐기한 다음 RH 및 중앙 시트 버클을 함께 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15mm 소켓
    • 3인치 익스텐션
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트를 쉽게 탈거할 수 없는 경우 유도성 가열 도구를 사용하여 접착 패치를 녹입니다. 볼트 주변에 유도성 가열 도구 코일을 놓은 후에 20초간 볼트를 가열합니다. 볼트가 냉각되도록 2분간 기다린 다음 볼트를 탈거하여 폐기합니다.

Install

  1. RH 및 중앙 시트 버클을 차체에 고정하는 새 볼트를 장착합니다.
    40 Nm (29.5 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    패스너가 RH와 중앙 버클 앵커 플레이트를 모두 관통하고 있는지 확인하십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    중앙 버클 앵커 플레이트의 가이드 슬롯이 RH 버클 앵커 플레이트의 핀과 정렬되어 있는지 확인하십시오.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15mm 소켓
    • 3인치 익스텐션
  2. 암 커넥터를 차체 스터드에 고정하는 브래킷을 장착합니다.
  3. RH 및 중앙 시트 버클 전기 커넥터를 연결합니다.
  4. 2열 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. 모든 창문을 올리고 모든 도어를 닫습니다.