2022-03-08

Cup Holder (Remove and Replace)

Correction code 15191802 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

교정 코드와 FRT
  • Cup Holder (Remove and Replace)용 Model 3: 15191802,
  • Cup Holder (2nd Generation) (Remove and Replace)용 Model 3: 15191812

NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Cup Holder (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
컵 홀더 하단 어셈블리를 센터 콘솔에 고정하는 나사
1.1 Nm (.8 lbs-ft)
  • Torx T20 소켓
  • 4인치 익스텐션
Reuse
암레스트 래치 그로밋을 컵 홀더에 고정하는 나사
1.6 Nm (1.2 lbs-ft)
  • Torx T15 소켓
  • 2인치 익스텐션
Reuse

Remove

  1. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  2. 센터콘솔 장식 트림을 탈거합니다. Decor Trim - Center Console - LH (Remove and Replace)을(를) 참조하십시오.
  3. 나사를 탈거하고 LH 및 RH 브라이트 스트립을 센터콘솔에 고정하는 탭을 분리한 다음 콘솔에서 스트립을 탈거합니다.
    1.6 Nm (1.2 lbs-ft)
  4. 암레스트를 엽니다.
  5. 컵 홀더 장식 트림을 컵 홀더 어셈블리에 고정하는 클립을 분리한 다음 센터콘솔 어셈블리에서 트림을 분리합니다.
  6. 보안 차체 컨트롤러 모듈 커넥터에서 전기 하네스를 연결 해제한 다음 차량에서 트림을 탈거합니다.
  7. 센터콘솔 전원 소켓 커넥터에서 전기 하네스를 연결 해제합니다.
  8. 센터콘솔 퍼들 램프 커넥터에서 전기 하네스를 연결 해제합니다.
  9. 스프링 캡의 소형 탭을 분리하고 소켓의 측면 개구부가 캡의 대형 탭과 정렬되도록 전원 소켓을 캡 안쪽으로 밀어 넣습니다.
  10. 캡의 탭을 분리하고 컵 홀더 어셈블리를 통해 전원 소켓 및 캡을 함께 빼냅니다.
  11. 컵 홀더에 퍼들 램프를 고정하는 클립을 분리한 후, 컵 홀더에서 퍼들 램프를 탈거합니다.
  12. 플라스틱 트림 공구를 사용해 컵 홀더 라이너를 컵 홀더에서 탈거합니다.
  13. 암레스트 래치 그로밋을 컵 홀더에 고정하는 나사를 탈거합니다.
    1.6 Nm (1.2 lbs-ft)
  14. 컵 홀더 하단 어셈블리를 센터콘솔에 고정하는 나사를 탈거하고 차량에서 컵 홀더를 탈거합니다.
    1.1 Nm (.8 lbs-ft)

Install

Installation procedure is the reverse of removal.