24/08/2023 04:43:03

헤드라이너(히트 펌프)(탈거 및 교체)

교정 코드 15203112 0.66 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

  1. Open all four doors
    Informational PurposesAn informational icon, calling your attention
    참고
    If vehicle is being powered down, Latch rear doors to prevent accidental closure
  2. Lower all four windows
  3. Move LH front seat forward
  4. Move RH front seat forward
  5. Remove RH side rail assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, 2x tether hooks, Pull the upper corner of the side rail then work your way to bottom, Pull the lower side rail toward LH to release clips, Remove 2x tethers by twisting and pulling away from housing, DO NOT remove the tethers from body side, must be replaced if removed
  6. Push open RH coat hook
  7. Pry open RH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips
  8. Remove RH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 2.5 Nm
  9. Release clips securing the RH upper B-pillar assembly and move aside
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top of trim to release the remaining clips
  10. Remove LH side rail assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, 2x tether hooks, Pull the upper corner of the side rail then work your way to bottom, Pull the lower side rail toward RH to release clips, Remove 2x tethers by twisting and pulling away from housing, DO NOT remove the tethers from body side, must be replaced if removed
  11. Push open LH coat hook
  12. Pry open LH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    참고
    2x securing tabs
  13. Remove LH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 2.5 Nm
  14. Release clips securing the LH upper B-pillar assembly and move aside
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips
  15. Move LH front seat backward and seat back downward
  16. Remove LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  17. Remove LH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
  18. Remove clip for LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  19. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 3 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
  20. Remove LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
  21. Remove LH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Extending the sun visor may allow for extra working room
  22. Remove LH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  23. Remove LH sun visor from headliner area
    Informational PurposesAn informational icon, calling your attention
    참고
    Fold sun visor to the closed and folded down position but do not latch in place
  24. Disconnect LH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  25. Remove lower quad camera cover
    Informational PurposesAn informational icon, calling your attention
    참고
    4x tabs, Press on the side of the cover with a trim tool to release some of the tabs
  26. Remove tether from lower quad camera cover
    Informational PurposesAn informational icon, calling your attention
    참고
    2x tabs, Depress tabs to remove tether
  27. Remove rear view mirror
    Informational PurposesAn informational icon, calling your attention
    참고
    Turn mirror counterclockwise to remove, do not twist by holding the mirror itself, it will separate from the stalk, twist from the stalk connecting the mirror to the mount
  28. Disconnect rear view mirror
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  29. Move RH front seat backward and seat back downward
  30. Remove RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  31. Remove RH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 1x tab, Release upper clip then pull mid A-pillar upward to remove from vehicle
  32. Remove RH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
  33. Remove RH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Extending the sun visor may allow for extra working room
  34. Remove RH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  35. Remove RH sun visor from headliner
  36. Disconnect RH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  37. Remove headliner harness clips from LH A-pillar area
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips
  38. Disconnect headliner harness
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  39. Release headliner from body
    Informational PurposesAn informational icon, calling your attention
    참고
    10x clips, Start by releasing rear portion of headliner then work your way forward to ease removal
  40. Remove headliner from vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance, Remove through passenger front door opening

장착

  1. Position headliner into vehicle for installation
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance, Install through passenger front door opening
  2. Install headliner to body
    Informational PurposesAn informational icon, calling your attention
    참고
    10x clips, Recommend assistance. EMEA only - If previous FOHC is equipped with e-call, config will require updating
  3. Install headliner harness clips to LH A-pillar area
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips
  4. Connect headliner harness
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  5. Connect LH sunvisor connector
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Push the connector and wire harness backward. If original sun visor check base is magnetic, install original sun visor, otherwise replace the sun visor to the latest revision (region specific)
  6. Install LH sunvisor onto headliner area
    Informational PurposesAn informational icon, calling your attention
    참고
    Fold sunvisor to the closed and folded down position then latch
  7. Install LH sunvisor fastener
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 3.5 Nm
  8. Install LH sunvisor bracket cover
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips
  9. Install LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  10. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clip, 3 guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, fully seat seal along trim
  11. Install clip for LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  12. Install LH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
  13. Install LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  14. Move LH front seat forward and seat back upward position
  15. Connect RH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector ,If original sun visor check base is magnetic, install original sun visor, otherwise replace the sun visor to the latest revision (region specific)
  16. Install RH sun visor into headliner area
  17. Install RH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 3.5 Nm
  18. Install RH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips
  19. Install RH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  20. Install RH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 1x tab, Align bottom tab then push on top clip to fully seat mid A-pillar, Make sure seal seat on top of trim
  21. Install RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips
  22. Connect rear view mirror connector
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  23. Install rear view mirror
    Informational PurposesAn informational icon, calling your attention
    참고
    Turn mirror clockwise to install, do not twist by holding the mirror itself, it will separate from the stalk, twist from the stalk connecting the mirror to the mount
  24. Install tether onto lower quad camera cover
    Informational PurposesAn informational icon, calling your attention
    참고
    2x tabs
  25. Install quad camera lower cover
    Informational PurposesAn informational icon, calling your attention
    참고
    4x tabs, Install the tabs closest to the rearview mirror assembly and push the cover up to secure
  26. Move RH front seat forward and seat back upward
  27. Install the RH upper B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim
  28. Install RH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 2.5 Nm
  29. Close RH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips
  30. Push RH coat hook closed
  31. Install RH side rail assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, 2x tethers, Replace tether if removed from body side, Install 2x tethers hooks to housing, Align the clips from bottom to top then press clips from top to bottom, Align the seal to sit on top of the trim
  32. Move RH front seat to original position
  33. Install the LH upper B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim
  34. Install LH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T25, 2.5 Nm
  35. Close LH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    참고
    2x securing tabs
  36. Push LH coat hook closed
  37. Install LH side rail assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, 2x tethers, Replace tether if removed from body side, Install 2x tethers hooks to housing, Align the clips from bottom to top then press clips from top to bottom, Align the seal to sit on top of the trim
  38. Move LH front seat to original position
  39. Raise all windows
  40. Close all four doors