2020-12-16

Check Strap - Door - Front - LH (Remove and Replace)

Correction code 10106052 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1454796-00-A 도구 키트, 창문 스위치

Torque Specifications

표 1. Torque Specifications: Check Strap - Door - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
체크 스트랩을 A필러에 고정하는 볼트
24 Nm (17.7 lbs-ft)
  • 13mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
체크 스트랩을 도어에 고정하는 너트
10 Nm (7.4 lbs-ft)
  • 10mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 전면 LH 도어 트림 패널을 탈거합니다. Panel - Door Trim - Front - LH (Remove and Install)을(를) 참조하십시오.
  2. 창문 스위치 도구를 도어 하네스에 연결하고 전면 LH 도어 창문을 완전히 올립니다.
  3. 전면 도어 스피커를 탈거합니다. Speaker - Front Door - LH (Remove and Replace)을(를) 참조하십시오.
  4. LH 전면 도어 체크 스트랩을 A필러에 고정하는 볼트를 탈거합니다.
    24 Nm (17.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    도어 체크의 볼트를 풀면 도어가 개방 한계를 넘어 제한 없이 열립니다.
  5. 플라스틱 트림 도구를 사용하여 체크 스트랩 씰을 도어에 고정하는 클립(3개)을 분리합니다.
  6. 체크 스트랩을 도어에 고정하는 너트(2개)를 탈거합니다.
    10 Nm (7.4 lbs-ft)
    • 10mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  7. 스피커 브래킷 개구부 안쪽에 접근하여 차량에서 체크 스트랩을 탈거합니다.

Install

Installation procedure is the reverse of removal, except for the following:

  • 패스너에 토크를 가하기 전에 체크 스트랩 씰을 체크 스트랩으로 이동하십시오.