Bracket - Passive Hood Strut - LH (Remove and Replace)
Correction code 11330102 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
스트럿 브래킷을 휠 아치 내부에서 휠 아치에 고정하는 볼트 |
![]() 13 Nm (9.6 lbs-ft) |
|
Reuse | |
스트럿 브래킷을 브래킷 상단에서 휠 아치에 고정하는 볼트 |
![]() 10 Nm (7.4 lbs-ft) |
|
Reuse |
Remove
- 후드 내 보관 유닛을 탈거합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.
- LH 전면 휠 아치 라이너를 탈거합니다. Wheel Arch Liner - Front - LH (Remove and Replace)을(를) 참조하십시오.
-
소형 일자 드라이버를 사용하여 가스 스트럿을 LH 패시브 후드 스트럿 브래킷에 고정하는 클립을 분리한 다음 브래킷에서 스트럿을 탈거합니다.
-
휠 아치 내부에서 LH 패시브 후드 스트럿 브래킷을 차체에 고정하는 볼트를 탈거합니다.
참고Use of the following tool(s) is recommended:
- 10mm 소켓
- 2인치 익스텐션
- 래칫/토크 렌치
-
브래킷 상단에서 LH 패시브 후드 스트럿 브래킷을 차체에 고정하는 볼트를 탈거한 다음 차량에서 브래킷을 탈거합니다.
참고Use of the following tool(s) is recommended:
- 6mm 육각
- 2인치 익스텐션
- 래칫/토크 렌치
Install
-
LH 패시브 후드 스트럿 브래킷을 차체에 장착한 다음 브래킷을 차체에 고정하는 볼트를 브래킷 상단에 장착합니다.10 Nm (7.4 lbs-ft)참고Use of the following tool(s) is recommended:
- 6mm 육각
- 2인치 익스텐션
- 래칫/토크 렌치
-
휠 아치 내부에서 LH 패시브 후드 스트럿 브래킷을 차체에 고정하는 볼트를 장착합니다.13 Nm (9.6 lbs-ft)참고Use of the following tool(s) is recommended:
- 10mm 소켓
- 2인치 익스텐션
- 래칫/토크 렌치
-
스트럿을 LH 패시브 후드 스트럿 브래킷에 장착한 다음 소형 일자 드라이버를 사용하여 스트럿을 브래킷에 고정하는 클립을 조입니다.
- LH 전면 휠 아치 라이너를 장착합니다. Wheel Arch Liner - Front - LH (Remove and Replace)을(를) 참조하십시오.
- 후드 내 보관 유닛을 장착합니다. Underhood Storage Unit (Remove and Replace)을(를) 참조하십시오.