2025-10-17

Brake Hose - Flexible - Rear - LH (Remove and Replace)

Correction code 33030502 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1079041-00-A 플레어 너트 크로우풋 세트
Informational PurposesAn informational icon, calling your attention
참고
이 절차는 퍼포먼스 및 비 퍼포먼스 후면 브레이크에 모두 적용할 수 있습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
Informational PurposesAn informational icon, calling your attention
참고
사용한 브레이크 오일은 현지 환경 규정에 따라 폐기합니다.
  • 2025-09-29: 잘못 정렬된 단계를 수정했습니다. 리프트에서 차량을 조정하고 장착 시 브레이크를 버니싱하는 단계를 추가했습니다.

Remove

  1. 12V/LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  2. 후면 LH 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  3. 후면 LH 브레이크 호스 아래에 오일 배출 용기를 배치합니다.
  4. 자운스 호스 브래킷의 브레이크 호스에서 브레이크 라인 튜브 너트를 탈거하여 오일을 배출합니다.
  5. 브레이크 호스를 자운스 호스 브래킷에 고정하는 볼트를 탈거한 후 브래킷에서 호스를 탈거합니다.
  6. 브레이크 캘리퍼 아래에 오일 배출 용기를 배치합니다.
  7. 가요성 브레이크 호스를 브레이크 캘리퍼에 고정하는 볼트를 탈거한 다음 차량에서 호스를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 및 와셔(2개)는 고정되어 재사용할 수 없습니다. 볼트가 풀렸거나 탈거된 경우 호스 어셈블리를 교체하십시오.

Install

  1. LH 후면 가요성 브레이크 호스를 차량에 배치한 다음 호스를 LH 후면 브레이크 캘리퍼에 고정하는 볼트를 장착합니다.
    42 Nm (31.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 및 와셔는 새 호스 어셈블리에 고정되어 있습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    브레이크 라인의 양쪽에 와셔를 하나씩 장착합니다. 와셔를 이중으로 쌓지 마십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    Mark the fastener with a paint pen after torquing.
  2. 자운스 호스 브래킷에 브레이크 호스 브레이크 호스를 장착한 후 호스를 브래킷에 부착하는 클립을 조입니다.
  3. 자운스 호스 브래킷의 브레이크 호스에 브레이크 라인을 삽입한 후 크로우풋 익스텐션을 사용하여 브레이크 라인 튜브 너트를 브레이크 호스에 장착합니다.
    16 Nm (11.8 lbs-ft)
  4. 차량 아래에서 오일 배출 용기를 치웁니다.
  5. 차량을 부분적으로 내리고 잠금 장치에 고정합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  6. 정비한 브레이크 호스에 대해 브레이크 캘리퍼를 블리딩합니다. 참조 항목: Brake Fluid Bleed - One Caliper.
  7. 후면 LH 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  8. 12V/LV 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  9. Perform a road test and burnish the brake pads. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure proper brake pedal feel and brake performance.
    Informational PurposesAn informational icon, calling your attention
    참고
    Add correction code 33013000 as a separate activity to the SV.