2020-12-16

Brightwork - Upper - LH (Remove and Replace)

Correction code 12200302 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Brightwork - Upper - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
브라이트 워크를 차체에 고정하는 나사
1 Nm (.7 lbs-ft)
  • Torx T20 소켓
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
  • 2인치 익스텐션
Reuse

Remove

  1. LH 도어를 엽니다.
  2. 전면 및 후면 기본 차체 씰을 아래로 당겨 LH 상단 브라이트워크에서 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    B필러 아플리케 상단의 씰은 분리할 필요가 없습니다.
  3. LH 상단 브라이트워크를 차체에 고정하는 푸시 리벳과 나사(10개)를 탈거한 다음 차량에서 브라이트워크를 조심스럽게 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    전면에서 후면으로 작업합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    도장 및 트림의 손상을 최소화하기 위해 보조 작업자의 도움을 받아서 후면 쿼터 글라스에서 브라이트워크를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    • 2인치 익스텐션
  4. 차체에서 그로밋(10개)를 탈거하여 폐기합니다.

Install

  1. 그로밋을 장착할 부분을 IPA(이소프로필알콜) 헝겊으로 닦습니다.
  2. LH 상단 브라이트워크를 장착할 차체에 새 그로밋(10개)를 장착합니다.
  3. B필러 코너에서 차체 쪽으로 씰을 누릅니다.
  4. 보조를 받아 후면 쿼터 글라스에 LH 상단 브라이트워크를 조심스럽게 장착합니다.
  5. 차체에 LH 상단 브라이트워크를 장착한 후, 차체에 브라이트워크를 고정하는 나사(10개)와 푸시 리벳을 장착합니다.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    • 2인치 익스텐션
    Informational PurposesAn informational icon, calling your attention
    참고
    후면에서 앞면으로 작업합니다.
  6. 후면 및 전면 기본 차체 씰을 위로 눌러 LH 상단 브라이트워크에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    각 씰의 후면 모서리에서부터 앞으로 작업하며, 씰이 브라이트워크와 완전히 체결되게 합니다. 올바르게 장착되면 씰 테두리가 보이지 않습니다.
  7. 균일하게 퍼지도록 각 개구부를 빙 둘러 씰 작업을 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    반드시 각 모서리에 씰을 밀어 넣습니다.
  8. LH 도어를 닫습니다.