2025-09-11

Glass - Roof - Fixed (Remove and Replace)

Correction code 10205002 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-12-10: 장착 전 글라스 검사 서비스 요구 사항에 대한 새로운 주의 사항을 추가했습니다.
  • 2024-03-26: 비드 너비를 13mm에서 12.5mm로 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in 장착 전 글라스 검사 before beginning this procedure.

Remove

  1. 모든 도어를 열고 모든 창문을 내립니다.
  2. 마스킹 테이프를 부착하여 차량의 도장을 보호합니다.
  3. 고정 루프 글라스에서 윈드실드, 차체 측면, 백라이트 글라스까지의 간격을 측정하여 기록합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    측정한 간격은 고정 루프 글라스 장착에 이용됩니다.
  4. WRD Spider 3 글라스 탈거 키트를 준비합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • WRD Spider 3 - 1571168-00-A
  5. 라인을 스타터 공구에 고정하고 고정 루프 글라스 어셈블리의 LH 후면 모서리에 있는 우레탄을 통과해 공구를 밀어 넣습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    헤드라이너 어셈블리 및 외부 도장이 손상되지 않도록 주의하십시오.
  6. 스타터 공구에서 라인을 분리하고 고정 루프 글라스 어셈블리 외부 주위에 라인을 감습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    글라스를 통해 충분한 길이로 당겨졌는지 확인하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    라인이 글라스 아래에 안착했는지 확인하십시오.
  7. 와이어 끝을 스타터 공구에 다시 연결한 다음 라인을 차량 안으로 다시 당깁니다.
  8. 고정 지점을 고정 루프 글라스 어셈블리의 내부에 고정한 다음 라인을 앵커에 고정합니다.
  9. 라인의 내부 면을 Spider 절단 도구에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Spider 도구의 지침을 따릅니다. 절단 도구의 개구부를 통과해 라인을 집어넣고 매듭을 묶어 라인을 제자리에 고정합니다. 스핀들이 올바른 방향으로 회전하지 않는 경우 절단 도구가 손상됩니다.
  10. Spider 절단 도구를 고정 루프 글라스 어셈블리의 내부 면에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    절단 라인의 방향을 기록합니다. 라인이 큰 풀리를 감싸고 90도 각도를 유지하는지 확인하십시오.
  11. 앵글 드라이버를 전기 드릴에 고정합니다.
  12. 드릴로 절단 도구의 스핀들을 돌려 고정 루프 글라스 어셈블리 탈거를 시작합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    라인을 90도 각도에 가깝게 유지하며 필요에 따라 절단 도구를 이동합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    플라스틱 보호대를 사용하여 탈거하는 동안 헤드라이너 어셈블리를 보호합니다.
  13. 고정 루프 글라스의 각 모서리에 흡착컵(2개)을 부착합니다.
  14. 보조 작업자와 함께 고정 루프 글라스를 차량에서 탈거합니다.
  15. 고정 루프 글라스에서 흡착 컵을 탈거합니다.
  16. 스크래퍼를 사용하여 차체에서 기존 우레탄을 제거한 다음 이소프로필 알코올로 차체 표면을 닦아 깨끗하게 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    우레탄 잔여물 두께가 1mm 이하인지 확인하십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이 단계에서는 절단 방지 장갑을 포함한 적절한 PPE를 착용하십시오.

Install

  1. 새 고정 루프 글라스의 각 모서리에 흡착컵(2개)을 부착합니다.
  2. 이소프로필 알코올 천으로 고정 루프 글라스의 리딩 에지를 닦아냅니다. 다음 단계를 계속 진행하기 전에 표면을 건조시킵니다.
  3. 이소프로필 알코올 천으로 차량의 우레탄 경로를 닦아냅니다. 다음 단계를 계속 진행하기 전에 표면을 건조시킵니다.
  4. 차체에서 우레탄 도포 경로를 따라 그리고 고정 루프 글라스를 탈거하는 동안 손상된 부위에 우레탄 프라이머를 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    최소한 1분 동안 프라이머를 건조합니다.
  5. 차량에서 마스킹 테이프를 떼어냅니다.
  6. 본래의 경로를 따라 차체에 우레탄을 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    우레탄 비드는 대략 너비 12.5mm 및 높이 20mm의 삼각형 단면을 가져야 합니다.
  7. 보조 작업자와 함께, 새 고정 루프 글라스를 차량에 장착하되, 아직 고정하지 않습니다.
  8. 글라스 후면의 기준점을 차체에 맞추어 정렬합니다.
  9. 고정 루프 글라스를 탈거하는 중 기록해 둔 간격 측정치를 적용하며 새 고정 루프 글라스를 차체 쪽으로 누릅니다.
  10. 윈드실드, 차체 측면, 백라이트 글라스와의 간격이 간격 측정치 내에 있는지 확인하고, 필요한 경우에는 조정합니다.
  11. 새 고정 루프 글라스에서 흡착컵을 탈거합니다.
  12. 테이프를 사용해 고정 루프 글라스를 임시로 고정합니다.
  13. 필요한 경우 윈드실드 및 백라이트 글라스 씰의 위치를 조정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    필요한 경우 글라스 세정제를 분무해 씰을 윤활합니다.
  14. 차량이 대략 2019년 4월 5일 이전에 제조된 경우: "roofGlassType" 구성을 업데이트해야 할 수 있습니다. 자세한 내용은 Toolbox 문서 141800을 참조하십시오.
  15. 우레탄이 양생된 후 마스킹 테이프를 떼어냅니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Do not drive the vehicle until the adhesive manufacturer’s recommended minimum drive-away time has passed. Dow Betaseal Express has a drive-away time of 1 hour minimum in temperatures of 0˚F (-18˚C) or warmer. If necessary, leave the tape applying pressure to the glass on the vehicle and advise the customer that they can remove it after 24 hours. Additionally, advise the customer that they should avoid high driving speeds and speed bumps for the next 24 hours.