09/10/2024 00:30:21

모듈 - 차체 컨트롤러 - LH(LHD)(히트 펌프)(탈거 및 교체)

교정 코드 17152112 0.48 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

  • 2023-11-13: Fixed error in routine.

탈거

  1. Open all doors and lower all windows.
  2. Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  3. Move the driver seat fully rearward.
  4. Disconnect 12V power. See 12V/LV 전원(연결 해제 및 연결).
  5. Remove the LH instrument panel end cap. See 엔드캡 - 계기판 - LH(탈거 및 교체).
  6. Remove the LH middle A-pillar trim. See 트림 - A필러 - 중단 - LH(탈거 및 교체).
  7. Remove the LH lower A-pillar trim. See 트림 - A필러 - 하단 - LH(탈거 및 교체).
  8. Remove the driver footwell cover. See 커버 - 발밑 공간 - 운전석(탈거 및 교체).
  9. Remove the driver knee airbag. See 에어백 - 무릎 - 운전석(탈거 및 교체).
  10. Remove the LH footwell duct. See 덕트 - 발밑 공간 - LH(LHD)(탈거 및 교체).
  11. Release the connector lock, and then disconnect the J7 LH front door electrical connector from the LH body controller module.
  12. Release the connector lock, and then disconnect the J9 LH front seat electrical connector from the LH body controller module.
  13. Release the connector lock, and then disconnect the J10 instrument panel electrical connector from the LH body controller module.
  14. Disconnect the J11 HVAC electrical connector from the LH body controller module.
  15. Disconnect the inline electrical harness connector X909 from the LH body harness, and then separate it from the LH body controller module.
  16. Release the connector lock, and then disconnect the J1 power connector from the LH body controller module.
  17. Disconnect the J6 front underhood storage connector from the LH body controller module.
  18. Disconnect the J5 body 3 electrical connector from the LH body controller module.
  19. Release the connector lock, and then disconnect the J4 body 2 connector from the LH body controller module.
  20. Disconnect the J2 body 1 electrical connector from the LH body controller module.
  21. Release the electrical harness clips that attach the LH body controller module to the vehicle.
  22. Move the LH body harness away from the LH body controller module.
  23. Remove and discard the nut that attaches the LH body controller module to the vehicle.
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 12 포인트 딥소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    • 2인치 익스텐션
  24. Slide the LH body controller upwards to release the W-clip, and then move the LH body controller module out from underneath the instrument panel.
  25. Remove the LH body controller module from the vehicle.

장착

  1. Maneuver the LH body controller module into position under the IP carrier. Align the W-clip with the body cutout, and then slide down to attach the LH body controller module to the body.
  2. Install a new nut that attaches the LH body controller module onto the body.
    6 Nm (4.4 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 12 포인트 딥소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    • 2인치 익스텐션
  3. Move the LH body harness towards the left side of the LH body controller module, and then attach the harness clips to the LH body controller module.
  4. Connect the J2 body 1 electrical connector to the LH body controller module , and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  5. Connect the J4 body 2 electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  6. Connect the J5 body 3 electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  7. Connect the J6 front underhood storage unit connector to the LH body controller module.
  8. Connect the J1 power connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  9. Connect the inline electrical connector X909 to the LH body harness, and then clip it to the LH body controller module.
  10. Connect the J11 HVAC electrical connector to the LH body controller module.
  11. Install the J10 instrument panel electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  12. Connect the J9 LH front seat electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  13. Connect the J7 LH front door electrical connector to the LH body controller module, and then engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the electrical connector is fully seated.
  14. Install the LH footwell duct. See 덕트 - 발밑 공간 - LH(LHD)(탈거 및 교체).
  15. Install the driver knee airbag. See 에어백 - 무릎 - 운전석(탈거 및 교체).
  16. Install the driver footwell cover. See 커버 - 발밑 공간 - 운전석(탈거 및 교체).
  17. Install the LH lower A-pillar trim. See 트림 - A필러 - 하단 - LH(탈거 및 교체).
  18. Install the LH middle A-pillar trim. See 트림 - A필러 - 중단 - LH(탈거 및 교체).
  19. Install the LH instrument panel end cap. See 엔드캡 - 계기판 - LH(탈거 및 교체).
  20. Connect 12V power. See 12V/LV 전원(연결 해제 및 연결).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Do not power on the climate control system until this procedure has been fully completed.
  21. Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  22. Connect to vehicle using Toolbox 3.0.
    Informational PurposesAn informational icon, calling your attention
    참고
    Vehicle connection is integrated into LH footwell cover.
  23. Perform a service CAN redeploy. See 소프트웨어 재설치 - Toolbox.
  24. Sit in the front passenger seat and close the RH front door.
  25. In Toolbox, click the Actions tab, and then type "PROC_VCLEFT" in the search field.
  26. Click PROC_VCLEFT_X_POST-REPLACEMENT-PROCEDUREvia Toolbox: (link)via Service Mode Plus: LowVoltage ➜ VCLEFT Post Replacement ➜ VCLEFT Post Replacement Procedure, and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    참고
    Keep the driver seat clear of all objects during calibration.
  27. Move the front passenger seat to the original position.
  28. Raise the RH front window and close the RH front door.
  29. Disconnect the laptop from the vehicle.
  30. Move the driver seat to the original position.
  31. Close the LH front door.
  32. Inform the customer that their liftgate opening height settings have been reset and to refer to the owner's manual for instructions on setting the liftgate opening height.